Trailer Hitch for 2013 Hyundai Veloster
Question:
Hi, Regarding a: Curt Trailer Hitch for the 2013 Hyundai Veloster Can a base, manual Veloster tow a small flatbed trailer less than 100 lbs tongue weight? I’d love to tow one yet, I’ve had transmission problems on my former Elantra, so I’m hesitant foolish? to try. Thanks
asked by: P C
Expert Reply:
With such a light trailer you'd probably be okay, but be aware that in the owner's manual, Hyundai states that towing a trailer with the 2013 Veloster isn't recommended.
If you decide to tow the trailer, you'll need the following:
Class I trailer hitch, part # C11254
Trailer wiring harness w/ 4-pole trailer connector, part # C56153
Ball mount, part # C45521
Trailer ball, part # A-80 for a 1-7/8 inch ball or # A-82 for a 2 inch ball
Hitch pin and clip, part # PC2
To see a hitch install video, click the provided link.
Products Referenced in This Question
1-7/8" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 1-7/8 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Stainless Steel - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Stainless Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Pin and Clip for 1-1/4" Hitches - 1/2" Diameter
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 1-1/4 Inch Hitch
- 1/2 Inch Diameter
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 100 lbs TW
- 1000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Recommended Hitch Mounted Bike Rack With Rear Bumper Clearance on a 2017 Chevy Cruze LT
- Q&A: Do 2016 Chevy Cruze LS and Limited Have the Same Hitch Fits
- Q&A: Thule Passage vs. Thule Gateway Pro Trunk-Mount Bike Rack for 2011 Subaru Forester
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Q&A: Is There a Trailer Hitch for a 2017 Hyundai Veloster
- Q&A: Recommended Trailer Hitch, Wiring, and Ball Mount for 2016 Hyundai Veloster
- Q&A: Equalizer Replacement Options for Dexter 13-122 Equalizer
- Q&A: Winch Recommendation to Replace Shelby 5352 on Trailer
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Hitch Receiver Sizes
- Article: Hitch Adapters and Extenders
- Article: Trailer Wiring Diagrams
- Article: Determining Trailer Tongue Weight