To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side interior trim panels in your rear cargo area.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (20 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required. Converter is made using SMT to ensure superior performance.It worked sweet as a dream. No problem at all to wire it up. Thank you. The only thing I'm looking for now is a trailer coupler that bolts to a flat piece of channel iron that I'm using for a trailer tongue. Hard to find.
George P.
10/1/2014
Works fine, no problems at all.Wish I would have found it sooner. Thank you.
Perfect fit
The Pre -wired connectors are well worth the extra expense as compared to the products that must be spliced . Easy and simple installation. Just read the directions.
Gary G.
4/11/2015
Still works like new , No problems
I was very satisfied with my purchase. I had the wiring harness installed in about 30 minutes and it worked perfectly. Thank You!
James H.
10/8/2019
It is still working perfectly. I dont anticipate any problems.
High quality products with easy to follow instructions! I have purchased two hitches and wiring harnesses and have never had an issue with either.
The wiring harness that I ordered from you was perfect it did the job that I wanted to do and I have still pleased with it thank you very much for your service and good quality of product. I needed it in a hurry to make a trip to Florida and it came in time to get it installed and be on my way so kudos to you for your good service.
Great product, super easy to install with no splicing! Just be sure to read the instructions carefully- the images aren't in color so it's hard to tell which wires go to which side of the car.
Literally plug and play, took 5 minutes!
fast delivery,easy installation,have yet to pull trailer to see if everything works. George.
Bought the kit for my 2000 Camry, installed in a snap. Was a bit confused at first on what side to install, they had left and right side on the label, wish they had labeled it driver/passenger. Other than that works great install time was less than 30 min.
Went together quickly and easily. It was just what I needed. Thanks
This product works great. A simple & quick install.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Patrick B.
10/2/2013
Glad to hear the harness worked out well for you. We do have some adjustable coupler systems that utilize channels welded to the front of the trailer. Rather than throw parts at you, we will be in touch so we can figure what you have and what you need. In the meantime, it would be a good idea to snap some photos of the channel and have them ready.