Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision
(59 reviews)
Price: $363.15
In Stock
Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision
Item # 3460001
Our Price: $363.15
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (59)
- Q & A (0)
- Photos
GCH Automotive Accessories and Parts - 3460001
- Backup Camera
- Third Brake Light
- Third Brake Light Camera
- For 8 Inch Factory Monitor
- GCH Automotive
Custom bezel with camera mounts behind your third brake light. Line up your fifth wheel or gooseneck trailer using your vehicle's factory monitor. Switch kit lets you toggle between views from your backup camera and third brake light camera.
Features:
- Custom bezel with camera mounts behind your third brake light so you can see into your truck bed
- Works with your 8" factory monitor
- Assists in connecting your fifth wheel or gooseneck trailer
- Only functions while in reverse
- Camera manually adjusts 360-degrees for a perfect angle into your truck bed
- Gives you a 150-degree viewing angle
- Rear assist marker lines generated by camera show distance from other objects
- 0 Lux night vision produces a quality picture in complete darkness without IR transmitters
- Switch kit allows you to toggle between truck bed camera and your factory backup camera
- Waterproof, aluminum camera resists dust and corrosion
- IP69-rated to protect against dust and close-range, high-pressure spray downs
- Installation - uses your existing hardware
- Drilling is required if you choose to mount the flip switch
Specs:
- Camera bezel dimensions: 17-5/8" wide x 4-3/4" tall x 1-1/8" deep
- Mounting hole spacing:
- Inner: 5-7/8" center to center
- Outer: 14-3/4" center to center
- Camera diameter: 1-1/2"
- Resolution: 620 Lines
- Voltage: 12V - 24V DC
- Wiring harness: 24' long
- 3-Year warranty
Rear Assist Lines
The rear assist lines generated by the system's camera make connecting your fifth wheel camper or gooseneck trailer a one-person job. The lines appear on your 8" factory monitor and show the distance from other objects, allowing you to accurately line up your connection point when hooking up your camper or trailer.
0 Lux Night Vision
0 Lux night vision produces a quality picture and gives you the flexibility you need when hooking up your camper or trailer. You can line up your connection point in low-light conditions at dusk, or in complete darkness at night without the aid of IR transmitters.
Switch Kit
The switch kit adds a new dimension to your current setup, allowing you to toggle between views from your truck bed camera and factory backup camera with the flip of a switch. The integrated flip switch can be mounted inside of your truck to give you a clean OEM look and easy access.
Simple Installation
Simply unscrew and unplug your factory third brake light. Once removed, set your new custom bezel with camera in place. Feed the 6' camera wire through the opening into your truck and re-install your factory third brake light in front of the custom bezel.
Connect your 6' camera wire to the 18' wiring harness. This combined 24' wire will extend through your head liner or door sill panel along the edge of the floor, up to the front of your truck, and connect with the included ground and power wiring harness. The power wire will run to your truck's battery.
The switch kit installs by connecting one end of the included T-harness into the factory plug behind your radio, and the other end into the back of your radio. The integrated power wire for the flip switch will run to 12V accessory power.
17FRDBRK360SW-K1 Truck Bed Camera for Factory 8" Monitor - Night Vision - Switch Kit
This Product Fits The Following Vehicles
- 2015 - 2020 Ford F-150
- 2017 - 2021 Ford F-250 Super Duty
- 2017 - 2021 Ford F-350 Cab and Chassis
- 2017 - 2021 Ford F-350 Super Duty
- 2017 - 2021 Ford F-450 Super Duty
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
- Wrong item was ordered
- Defective
- Product did not meet expectations
Customer Reviews
Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision - 3460001
Average Customer Rating: 4.7 out of 5 stars (59 Customer Reviews)
Custom bezel with camera mounts behind your third brake light. Line up your fifth wheel or gooseneck trailer using your vehicle's factory monitor. Switch kit lets you toggle between views from your backup camera and third brake light camera.by: Michael 03/29/2024
Fairly easy to install. Just make sure the connections are tight. I had one that was not completely tight, went back over the connectors and then it worked good. Good image on my factory synk4 8” display
by: Rusty T02/06/2024
With a fifth wheel hitch in the bed, I struggled to hit the pin hooking up. With this camera it's a snap. Hookup the first try every time. Install was easy if you follow the video and take your time.
by: Chip09/04/2022
It's unclea whether the voltage regulator in the camera cable failed or the camera cable was chafed by something moving behind the dash, but the company was excellent in making good. A bit of a pain to replace it, but the second camera is working very well. Very clear picture.
by: Butch S12/12/2023
2020 Ford F-350 Super Duty
Looks like original equipment and should make hookups much easier. Has great view.
by: Samuel02/15/2024
It’s not as clear of a picture as factory. I still find myself looking over my shoulder.
by: Stacy12/01/2021
I am incredibly happy with this back up camera for our 2019 F350. The picture is crystal clear and the wiring allowed us to view on the factory truck screen. etrailer was informative and their experience helpful in our decision to purchase this camera.
Stacy
12/2/2022
1 year in and this camera is still doing great. Very clear image.
by: Corey07/10/2023
2018 Ford F-350 Super Duty
Easy install, clear picture, instructions could be improved. Make sure to use both ground wires or camera will not work. Would be nice to be able to zoom in with camera both overall great product
by: Michael05/17/2019
2019 Ford F-250 Super Duty
For being an after market item it is a great camera. The installation video on how to install was very informative down to the last detail. I installed this camera on my 2019 Ford F250 SD that had the sync 3 8" screen and it went together very well.
The ONLY thing I would have liked to see is a "centered line" in the middle of the picture to help guide the king pin onto the 5th wheel hitch when hooking up my trailer.
I know that there are other newly acquired F-Series buyers who, after years of hooking up 5th wheels by just looking into your rear view mirror, never realized that with these new Ford Trucks that you lose the line of sight due to a higher rear seat back that covers over 8 inches of the rear window so you can't see your hitch. Otherwise, I would have probably had the Ford original camera in the 3rd brake light option.
Too bad Ford doesn't sell the camera's to the public as they are losing out of a bunch of money!!!
Michael
5/17/2020
Same as mentioned above
by: Michael10/05/2020
The only disappointment is you can’t zoom in on the ball in the box but easy installation !
by: Jim10/07/2020
My bed camera works great. Etrailer really stepped up to the plate for me. I installed it and could not get the camera to work after double checking my connections and the instructional video. We determined that the jumper harness was bad. They shipped out another camera system before I could get back to them and let the know the distributor was about 20 miles from me and they agreed to exchange the jumper harness. They even helped me test it on my truck before I left. Thank you Etrailer
Jim
10/8/2021
Love it. I have gotten to where I can back right over without getting out and checking several times.
by: Cory 12/11/2022
Installation was straight forward and it has worked as expected for over a year, now. It works perfect for hooking up our gooseneck in our extended cab truck where we can't see in the bed.
by: Michael S02/27/2021
Easy to install by just watching the video. I wired it to the Ford auxiliary switches as was shown on the video. This will take the guesswork out of hooking to my gooseneck 5th wheel.
Michael S.
2/28/2022
Camera is awesome. We have had it installed over a year now and it works perfectly
by: Andy 11/29/2020
Quality is descent. Would be nice to be able to manually zoom for better close up. The camera doesn’t work well with Trucks with bakflip (shortbed)cover if you using to hook-up to gooseneck. You can’t see the ball at all. Need about an inch more clearance. But overall love the camera. Without a cover works great.
by: Eric 10/31/2021
The unit was installed on 10/30/21. Works just like it should. Gives an excellent view of gooseneck ball and inside pick up bed. The camera angle is adjustable as well. The only thing I did was replace toggle switch with a more "clean" looking finger switch. Didn't like the toggle switch. Very satisfied with the camera. Should make it much easier to connect the trailer.
by: 01/21/2022
The instruction sheet was a joke, no value. I had a little trouble figuring out how the power gets to the camera, this is not on the instructions.The toddle switch that came with it exploded after I installed it. I got a better switch and changed. I added to the instruction sheet to include the connecting wires between the camera and the plugins to the truck screen.
Thomas M.
1/22/2022
I will have Customer Service reach out to you. I am also attaching a video detailing the installation process.
by: Ed05/18/2021
The camera is great, I can backup to my 4th wheel camper and hookup by myself. The only issue I would say is you have to totally remove the front part of your truck to hook it up.
Ed
5/18/2022
Great product, no issues
by: John 06/01/2021
Ford F-150
I installed on a f150 platinum and it worked great. I since have gotten another truck that had it from the factory. Very worthwhile if you have a fifth wheel or goose neck trailer.
by: Teddy 05/05/2023
2021 Ford F-250 Super Duty
Great product. Easy to install and connect. Perfect view. Better picture than the factory camera!
by: Martinez03/06/2022
2020 Ford F-250 Super Duty
The camera works great. Installation process was pretty simple. I watched the online installation video. The only issue I had, was the small "capped off" ground wire, that wire was never mentioned in the installation video. I knew it was labeled "ground", but it had a cap, almost as if it was terminated. Once I removed the cap and grounded the wire, the camera worked flawlessly.
by: Charles 01/21/2021
Love it! Makes hitching up my 5th wheel super easy. It even survived a few drive through car washes before I realized I probably shouldn't be doing that.
by: Thomas03/29/2021
Your install video saved the day. Product works as advertised and I like how it uses the factory monitor and the upfitter switch. Ford sure likes to hide those pass through wires though.
Thomas
3/30/2022
Still works great. No problems whatsoever.
by: Tony B03/31/2021
2019 Ford F-150
Easy install, works great, makes it very easy to hook up my 5th wheel camper now.
by: Mike 07/25/2020
2020 Ford F-250 Super Duty
Hooked it up and runs great, just had a minor issue with the installation but e-trailer representative fixed my problem by phone quickly. It was my fault didn't hook all wires. Mike
by: Tom T05/18/2020
This rearview camera was easy to install and has worked perectly.
by: Thomas12/14/2021
I followed the video installation exactly for my 2018 Ford F-250. At first, I failed to connect the tiny ground wire on the smaller jumper and the system didn’t work. Once properly grounded - everything works perfectly.
25
59
Show More Reviews
See what our Experts say about this GCH Automotive Accessories and Parts
- What Screen Size Is On a 2020 Ford F-250 Super Duty 8" or 7"? Your 2020 Ford F-250 was only available with either a 4.2", or 8" in dash screen. This measurement is taken diagonally and often the visible area is often covered slightly around the edges with a trim kit. This may explain why there is some confusion on the screen size for adding a Custom Third Brake Light Camera for 8" Factory Monitor # 3460001.
view full answer... - Where Does Wiring for Third Brake Camera Kit for 2020 Ford F250 XLT Run ToIf you want to see the entire install process of the third brake light camera kit # 3460001 for your 2020 Ford F-250 check out the linked video on this page. We ran the wiring up to the engine bay area which is the only and best place to run the wiring.
view full answer... - Does Truck Bed Cargo Camera for 2016 Ford F-150 With 8 Inch Screen Work When Not in ReverseYes, you can use the Truck Bed Cargo Camera for 8" Factory Monitor - Switch Kit # 3460001 that fits your 2016 Ford F-150 with an 8" factory monitor as an observation camera so you can see your truck bed. What you will need to do is simply wire it to a constant 12 volt power source (most people wire it to their reverse lights) and use the toggle switch to turn the camera on and off so you can view the bed when needed. I have added a link to a review and install of the Truck Bed Camera #...
view full answer... - Third Brake Light Backup Camera that Fits 2020 Ford F-250We do not have any tailgate style cameras for your 2020 Ford F-250 but we do have a camera kit that fits just below the third brake light with the GCH part # 3460001 that fits your truck.
view full answer... - Is Camera Angle of Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 AdjustableThe camera of the Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 can be adjusted. Around the lens there are 4 indentations that you can press into to push the camera angle more to that side.
view full answer...
- Will a Toolbox Block the GCH Truck Bed Camera on 2021 F-250 Super DutySince the toolbox you have is up against the cab it should not pose a problem for the Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision # 3460001. The camera manually adjusts 360 degrees and has a 150 degree viewing angle so even if your toolbox sticks out quite a bit you can adjust the camera accordingly. I have attached a review video as well as an installation video on a 2017 F-250 Super Duty for your reference.
view full answer... - How To Install The Custom Third Brake Light Camera For 8" Monitor On 2021 Ford Super DutyIf you have the factory auxiliary switch then just wire the Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision # 3460001 to that. If you don't have the factory auxiliary switch then you will want to utilize that toggle switch so that your camera knows when to turn on/off. I went ahead and attached an installation video on a 2017 Super Duty which will be a very similar process. It shows how to wire the entire system so you won't have to guess where anything goes; instructions...
view full answer... - Is Camera Angle of GCH Truck Bed Cargo Camera AdjustableThe ball socket of the Truck Bed Cargo Camera # 3460001 that you referenced is pretty tight but it is adjustable. What you'll want to do is use a small screwdriver to apply pressure into the screw hole I pointed out which will allow the socket to point down.
view full answer...
- How to Ground Custom Third Brake Light Camera for 8" Factory Monitor For Ford F-250/F-350 Super DutyThe ground wire from the Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision part # 3460001 needs to be grounded to the steel brace that runs across the dash using a ring terminal and self tapping screw. If the unit does not have a decent ground it will not work properly. If you take a look at the attached video starting at the time stamp of 12:20 our installer shows how to ground the camera. The Custom Third Brake Light Camera for 8" Factory Monitor part # 3460001 fits...
view full answer... - Can GCH Automotive Custom Third Brake Light Camera Go Through Car WashAccording to the owner of GCH Automotive, the # 3460001 camera can be ran through a car wash. Just make sure the gaskets are installed properly. If they aren't installed properly, the camera can leak. It's also important that the mounting screws aren't overtightened. This will deform the plastic and can also cause warping.
view full answer... - How To Install Custom Third Brake Light Camera On 2020 Ford F-150The Custom Third Brake Light Camera part # 3460001 which is a fit for a 2020 Ford F-150 with 8" monitor installs rather easily with only a few connections. There is a plug that ties into the factory harness and then a switch which gets run to a keyed power source. I have attached a snip of these instructions for you below.
view full answer...
- 3rd Brake Light Backup Camera for 2019 Ford F-350 That Can be Viewed While in DriveYou should be able to wire the power for the camera located at the 3rd brake light so that it has constant power and then it is switched on/off manually. If the current camera doesn't have that capability then you can install the Truck Bed Cargo Camera for 8" Factory Monitor - Switch Kit # 3460001 on the 2019 Ford F-350 and it can be wired this way. I reached out to my contact at GCH Automotive who confirmed this. The only thing that you'll have to check out is if Ford automatically "locks...
view full answer... - Can the Custom Third Brake Light Camera for a 2020 Ford F-250 Be Wired To An Existing In-Cab SwitchThe Custom Third Brake Light Camera for 8" Factory Monitor part # 3460001 could pretty easily be wired to an existing switch you have in the cab but I would not be able to offer much advice on this as it's designed to be used with the included toggle switch. I will however say that you would need to maintain the fuse size recommendation for the system. It's a two wire switch so installation should be super simple.
view full answer... - How Long Does it Take to Install Custom Third Brake Light Camera on 2020 Ford F-350 Super DutyIt can be difficult to give a truly accurate estimate for the length of time it takes to install the Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 on your 2020 Ford F-350 Super Duty. The time really depends on how comfortable one is with this type of work and any type of previous install experience. It isn't overly difficult but it can take some time to route the wiring so expect a few hours to do the install. To get a better idea of how long it can take I recommend...
view full answer... - Will Truck Bed Cargo Camera For 2020 Ford F-250 Super Duty Be Blocked By ToolboxThe Truck Bed Cargo Camera for 8" Factory Monitor part # 3460001 does feature a 150 degree angle image and 360 degree adjustable camera but what matters the most to you is that it is high enough above your truck bed that you'd be able to see over your tool box and see anything into your truck bed behind it like a gooseneck ball. I attached an install video for this for you to check out as well.
view full answer...
- Third Brake Light Camera Kit for 2019 Ford F-550For your 2019 Ford F-550 we have the GCH third brake light camera kit part # 3460001 which integrates into the factory console display of your truck and shows you what's behind the cab of the truck. I attached an install video for this kit for you to check out as well.
view full answer... - Installation Instructions for the Truck Bed Cargo Camera # 3460001 on a 2017 Ford F-150I've seen the instructions for the Truck Bed Cargo Camera # 3460001 and they are adequate but not super detailed. We do have our review video, which I've linked for you, that quickly shows you where they ran the wiring. I took a picture of the instructions (as the manufacturer currently doesn't have them available digitally) for you to check out. Using the instructions and the video will give you enough info for the installation on your 2017 Ford F-150.
view full answer...
- Should The Custom Third Brake Light Camera 3460001 Work In Colder Temperatures?The way the Custom Third Brake Light Camera # 3460001 is designed, you should not be having any problems at below freezing temps. I cannot say I have ever heard this complaint in regards to any of the RV/Truck cameras that we sell here. My father-in-law has a similar camera on his Chevy truck. Last winter we has a cold spell with several days around or below zero, and the camera worked without issue. It makes me think that somehow moisture has gotten inside the camera, and when temps get...
view full answer... - Recommended Back Up Camera For A 2021 Ford F-350 Super DutyWhen installing a backup camera on your 2021 Ford F-350 Super Duty The Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision # 3460001 it will allow you to see the back of the truck and use your custom monitor to see what is going on while backing up. This camera's custom bezel mounts behind your third brake light. You can line up with your fifth wheel or gooseneck trailer using your Ford F-350 Super Duty's factor monitor. This camera only functions when in reverse. it...
view full answer... - Will the Radio/Audio Stop Playing When You Switch to the Third Brake Light Camera ScreenI contacted the manufacturer about the audio when using the Custom Third Brake Light Camera # 3460001 on your 2019 Ford F-150. Per the manufacturer, only the video feed should be interrupted and your radio/audio should continue to play.
view full answer... - Can Truck Bed Cargo Camera # 3460001 be Installed and Wired to In-Cab Switch on 2018 Ford F-350Yes, the Truck Bed Cargo Camera # 3460001 will work with your 2018 Ford F-350 as long as you have the 8" factory monitor. You can also wire it to your cab switch just like we did in the attached installation video on a 2017 Ford F-250. The installation should be the same so you can use the video as a guide for your application.
view full answer...
- Could Install Harness of Truck Bed Cargo Camera # 3460001 Install Through Passenger Side GrommetMost likely you could install the Truck Bed Cargo Camera # 3460001 how you were describing, but since that's not how we installed it or how GCH recommends the install we don't have a way to confirm it would work. You could pretty easily attempt to install it that way and if the harness isn't the right length or it doesn't work for any other reason you could just go with the routing you saw in the install video that I also attached.
view full answer...
- Does Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 Allow Switching Camera ViewsYes, one of the really great things about the Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 is the fact that once installed it allows you to easily switch between the views of the third brake light camera and the tailgate camera. I attached an install video for this for you to check out as well.
view full answer... - Will the Truck Bed Cargo Camera Part # 3460001 Replace the Tailgate Camera on a 2018 Ford F-350Yes, the Truck Bed Cargo Camera part # 3460001 which is correct for your 2018 Ford F-350 will work with the factory backup camera disconnected. In fact, it can be used to replace the factory backup camera so you no longer have the disconnected message. In order to do this you will just want to install the camera like normal but leave out the switch.
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Video by:
Andrew K
Video Edited:
Dustin K
Video Edited:
Chris R
Installed by:
Cole B
Installed by:
Hayden R
Updated by:
Leah S
Updated by:
Adam Y
Edited by:
Amanda M
Test Fit:
David F
Written by:
Halie H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Chip
9/5/2023
Excellent customer support. Replacement has worked reliably ever since.