Is Camera Angle of Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 Adjustable

Question

Question:

can the installed bed camera be turned slightly or is it permanently positioned at the factory angle?

asked by: Paul

0

Expert Reply:

The camera of the Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 can be adjusted. Around the lens there are 4 indentations that you can press into to push the camera angle more to that side.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Custom Third Brake Light Camera #3460001 that you referenced does fit your 2020 Ford F-250 and while it comes with a switch setup to use it might be possible to wire it to the switch setup you mentioned. It can be viewed when not in reverse like…

view full answer...

Answer 2

Most likely you could install the Truck Bed Cargo Camera #3460001 how you were describing, but since that's not how we installed it or how GCH recommends the install we don't have a way to confirm it would work. You could pretty easily…

view full answer...

Answer 3

You should be able to wire the power for the camera located at the 3rd brake light so that it has constant power and then it is switched on/off manually. If the current camera doesn't have that capability then you can install the Truck Bed Cargo…

view full answer...

Answer 4

When installing a backup camera on your 2021 Ford F-350 Super Duty The Custom Third Brake Light Camera for 8" Factory Monitor - Night Vision #3460001 it will allow you to see the back of the truck and use your custom monitor to see what is going…

view full answer...

Answer 5

Yes, one of the really great things about the Custom Third Brake Light Camera for 8" Factory Monitor #3460001 is the fact that once installed it allows you to easily switch between the views of the third brake light camera and the tailgate…

view full answer...

Answer 6

Yes, you can use the Truck Bed Cargo Camera for 8" Factory Monitor - Switch Kit #3460001 that fits your 2016 Ford F-150 with an 8" factory monitor as an observation camera so you can see your truck bed. What you will need to do is simply…

view full answer...

Answer 7

To add two side cameras to your Furrion Vision S Wireless RV Backup Camera System with 5" Screen #FOS05TASF, you can use the Marker Light RV Side Cameras #FCE48TASL. I can understand your concern with the trailer having all LED lights, but it…

view full answer...

Answer 8

According to the owner of GCH Automotive, the #3460001 camera can be ran through a car wash. Just make sure the gaskets are installed properly. If they aren't installed properly, the camera can leak. It's also important that the mounting…

view full answer...

Answer 9

The Truck Bed Cargo Camera for 8" Factory Monitor - Switch Kit #3460001 hasn't been tested for this application yet, but backup cameras can be installed to the running light circuit so they can get constant power and be used as observation…

view full answer...

Answer 10

The Custom Third Brake Light Camera for 8" Factory Monitor part #3460001 could pretty easily be wired to an existing switch you have in the cab but I would not be able to offer much advice on this as it's designed to be used with the…

view full answer...

Answer 11

I've seen the instructions for the Truck Bed Cargo Camera #3460001 and they are adequate but not super detailed. We do have our review video, which I've linked for you, that quickly shows you where they ran the wiring. I took a picture of the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is Camera Angle of Custom Third Brake Light Camera for 8" Factory Monitor # 3460001 Adjustable

Product Page this Question was Asked From

Continue Researching