How to Determine Proper Spacing Between Tire and Fender for Clearance on 3000 LB Trailer
Question:
What is the proper spacing between fender and tire on a 3000 pound trailer
asked by: Nick
Expert Reply:
Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for potholes and bumps.
If you want to get precise, on an underslung trailer (the springs are mounted under the axle), you should measure the distance between the bottom of your frame and the top of your axle. Add two inches to that measurement and you should have adequate clearance when your trailer is fully loaded.
If you are shopping for fenders, our most popular weld-on trailer fender for 14-15" wheels is # HP36VR. The most popular bracket-mounted fender for 14" wheels is # F008554, which mount on brackets # PF775-BKT-2.
I've also included a link to our Trailer Maintenance Schedule for your convenience.
Products Referenced in This Question
Galvanized Steel, L-Shaped, Bolt-On Brackets for Plastic, Single-Axle Fender PF775X21W - Qty. 2
- Accessories and Parts
- Trailer Fenders
- Mounting Hardware
- 4 Inch Wide
- Brackets
- 7 Inch Tall
- Redline
more information >
Product Page this Question was Asked From
Single Axle Trailer Fender w/ Backing Plate - Steel - 14" to 15" Wheels - Qty 1
- Trailer Fenders
- No Step
- 14 Inch Wheels
- 15 Inch Wheels
- 9 Inch Wide
- 32 Inch Long
- Steel
- Bolt-On
- Weld-On
- For Single-Axle Trailers
- etrailer
more information >
Continue Researching
- Article: Trailer Tire Sizing
- Shop: Tandem Axle Teardrop Fenders w/ Backing Plates - 15" to 16" Wheels - Qty 2
- Shop: Mounting Brackets for Trailer Fender - 13"/14"/15" Wheels - Galvanized Steel - Qty 2
- Shop: Timbren Axle-Less Trailer Suspension - Heavy Duty - Long Spindle - 4" Lift - 5 Bolt - 3.5K
- Shop: Tandem Axle Teardrop Trailer Fenders for Enclosed Trailers - 14" to 15" Wheels - Qty 2
- Shop: Loadstar 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 5 on 4-1/2 - Load Range C
- Shop: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 3.19" Pilot - Stainless Steel
- Shop: Easy Grease Trailer Idler Hub Assembly for 6K Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Fifth Wheel Hitch
- Search Results: trailer fenders
- Q&A: How to Determine Fender Clearance when Timbren Axle Less TASR5200S03 is Installed on Trailer
- Q&A: What is Minimum Trailer Tire to Fender Clearance
- Q&A: Recommended Hub for 15 Inch Wheel On 3,500 Lb Timbren Heavy-Duty Axle-Less Suspension
- Search Results: 3500 lbs axle kit
- Article: Trailer Wiring Diagrams
- Search Results: hp64vr
- Article: Where to Position the Trailer Axle?
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Recommended Spacing Between Trailer Tire and Inner Fender
- Search Results: 480~12 trailer tires and wheels
- Search Results: trailer lights
- Video: Optronics Trailer Lights - Tail Lights - STL76RB Review
- Article: Rust Prevention
- Video: Optronics Trailer Lights - Tail Lights - STL87RCB Review
- Video: Review of Malone Trailers - Crossbar Conversion Kit - MPG475
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Q&A: Torque Settings For Wheel Lug Nuts For Boat Trailer And utility Trailer
- Q&A: Proper Way to Tighten Trailer Spindle of Castle Nut
- Shop: Trailer Wiring
- Q&A: Outside Diameter of Deka Wire - Jacketed 6-Wire - per Foot