Customers compare STL76RB to these similar products
Products Featured in this Video
Today were looking at the Optronics Long, Thin, Oval LED Trailer Stop, Turn and Tail Light, part number STL76RB. This red light strip functions as a stop, turn, and tail light. It has a sealed waterproof housing and lens unit. It comes with 11 Super LEDs or light emitting diodes. It surface mounts on 12-7/8 inches on centers.… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…
view full answer...If you have a 5 on 4-1/2 inch bolt pattern on your hub with 8 inch wheels, you will be able to use the 10 inch wheels with a 5 on 4-1/2 inch bolt pattern on that hub. The center hole diameter on the 8 inch wheels and the 10 inch wheels are the same…
view full answer...For your application you need to stick with your 8" wheels, otherwise you're looking at tires with a larger width and will likely rub against the trailer frame as you stated. Unfortunately there aren't any 10" wheels with an offset…
view full answer...You can use your Hobie carriers on your Malone MicroSport LowBed Trailer #MPG464-LB with the Malone Installation Hardware for Hobie Style Carriers #MPG5576-6. I have added a cut out of the instructions and linked them below but you just need to…
view full answer...I have a couple of option that fit in your size range but only the Kenda 205/50-10 Bias Tire part #AM90016 has the 10" rim overall it is 18.3" in diameter so it is really pushing your clearance range. The second option is the largest…
view full answer...I have a couple recommendations as we do not recommend using lift blocks likes those used on a vehicle axle for a lift. First since your axle sits above your leaf springs you can use the Over-Under Conversion Kit #K71-384-00 to place your axle below…
view full answer...Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for…
view full answer...I have two options for you to raise your trailer and gain more clearance between the fender and tire. The most cost effective option would be to flip the axles with a Dexter Trailer Springs Over-Under Kit part #K71-384-00 or part #K71-385-00. That…
view full answer...The Single Axle Trailer Fender #HP66VR is 36" long, and while it would be able to accommodate a 32" diameter tire, you generally want to leave about 4-1/2" or more when it comes to clearance between the tires and fenders. The reason…
view full answer...The numbers at the end of the two trailer tire sizes you mentioned are the wheel size they are intended to fit so what you are wanting to do is not possible. The size 4.8-12 is for a 12 inch wheel and the 4.8-8 is for an 8 inch wheel. So to go to the…
view full answer...The Dexter Trailer Hub Assembly you referenced, part #AKIHUB-440-2-1K is known as an idler hub. An idler is a hub that is no provisions for trailer brakes. It has no brake drum. Part #8-276-5 is an example of a hub/ drum that has a brake drum that…
view full answer...The Roadmaster Spare Tire Carrier #RM-195125 is going to likely be your best option. The only other option would be a Carrier #e98ZR you would have to remove to open the door. I have added an image with the length of the carrier below as you may…
view full answer...