Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
(202 reviews)
Price: $200.94
In Stock
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
Item # C13343
Our Price: $200.94
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (202)
- Q & A (0)
- Photos
CURT Trailer Hitch - C13343
- Class III
- 2 Inch Hitch
- 3500 lbs GTW
- Concealed Cross Tube
- CURT
- 525 lbs TW
- Custom Fit Hitch
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.
Features:
- Custom fit is designed specifically for your vehicle
- Precision, robotic welding maximizes strength and improves fit
- Bolt-on installation - no welding required
- Complete hardware kit and installation instructions included
- Lifetime technical support from the experts at etrailer.com
- Gloss black powder coat finish over protective base coat offers superior rust resistance
- Sturdy, square-tube design
- Ball mount, pin and clip sold separately
- Hitch assembled in the USA
- Mounting hardware may be imported
Specs:
- Receiver opening: 2" x 2"
- Rating: Class III
- Maximum gross trailer weight: 3,500 lbs
- Maximum tongue weight: 525 lbs
- Not rated for use with weight distribution systems
- Limited lifetime warranty
etrailer.com Technical Support
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
13343 Curt Class 3 Trailer Hitch Receiver
Installation Details
This Product Fits The Following Vehicles
- 2011 - 2020 Toyota Sienna
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Did not arrive in time
- Wrong item was ordered
- Did not fit
Customer Reviews
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" - C13343
Average Customer Rating: 4.8 out of 5 stars (202 Customer Reviews)
This fully welded trailer hitch receiver bolts onto your vehicle's frame with no welding required. Powder coated steel is sturdy and corrosion resistant.by: Marty S07/21/2022
2017 Toyota Sienna
Quick delivery, easy install of the hitch with two people. Definitely watch the installation videos as the paper directions can become confusing at times. As suggested,I did NOT remove the bumper. Also, I did cover the holes where the rubber plugs were removed with the stickers that covered up the weld nut holes and duct tape to keep debris out. Will work out great for bike rack and small trailer towing. I also like that it is tucked away behind the vertical plane of the bumper so that its not a shin bitter. :)
by: Jay Owen07/02/2022
Easy install. Very clean looking hitch. The only part that's visible is the receiver. This is way better than a factory installed Toyota hitch.
Jay O.
7/4/2023
After one year this trailer hitch is going strong and looking good. 4 inch rise for the ball works good.
by: Jim07/09/2023
The hitch receiver fit like a glove behind the Sienna’s bumper. Easy to assemble and great clearance.
by: Matt08/11/2023
2015 Toyota Sienna
Nice low profile hitch for a Sienna. Easy to install. I installed it by myself. I highly recommend having a helper to lift it into place. Also, if you don’t have access to a lift—which I suspect is most people—get yourself some car ramps and chocks because you’ll need room to maneuver. (That’s the annoying thing about installation videos—including eTrailer’s: who has a lift in their home garage?)
by: Gino 04/29/2024
Easy to install and seems sturdy. Have pulled a trailer a couple of times with no problems.
by: Karl01/18/2023
Fit perfectly, one man install, paint holding up fine, the reciever is properly sized. Would highly recommend.
Karl
1/19/2024
Still excellent!
by: Cody03/31/2023
I had bought the different model number that wasn’t concealed from somewhere else. I saw e trailers install video of the concealed hitch model and quickly realized I needed to switch models so I didn’t have to cut a bunch of plastic and have the bar showing. I was worried about shipping because we were on a time crunch, I received my product in less than 48 hours and was able to install quickly and with ease with the help of etrailers video! etrailer for the win!
by: Steve 10/06/2022
Great hitch, good instructions and easy install. I love that the bulk of the hitch is hidden, and only the receiver is exposed - looks very OEM.
Steve
10/8/2023
1 year update... hiding up well, finish is still good I oil it, no complaints!!
Mike L.
10/25/2023
@Steve We're glad to hear that you're happy with your # C13343 Curt trailer hitch!
by: Tim01/19/2024
Great trailer hitch, well packaged and shipped fast. George at etrailer is great to deal with. Thanks
by: Greg09/16/2023
2020 Toyota Sienna
I haven't even had a chance to install this product. Why? Because the packing of this product was so poor that it arrived on my door with the box half torn open. Any bolts/washers/necessary hardware that should have been included no doubt fell out one of the many tears/holes. I'm half surprised the hitch itself wasn't sticking halfway out of the box. Would update later once the actual product is installed, but am unable to do so right now.
Jenny N.
9/21/2023
I am sorry that it was delivered this way. I can see that Customer Service is sending our replacement hardware to you.
by: Mahlen09/22/2018
2015 Toyota Sienna
I ordered this hitch on Wednesday (with free shipping), received it on Friday and installed it on Saturday. It fits perfectly on my 2015 Sienna. I had a Drawtite hitch installed which I removed to install this Curt concealed hitch. The Drawtite kept bottoming out with a light duty trailer attached. I installed this by myself, but a second person would be helpful. It took me roughly 2 hours total to remove the Drawtite and install this one. I backed the car up on ramps and loosened the tailpipe hanger behind the right rear wheel. Here is the way I did the 2-man job by myself (I'm 73 yrs. old). After removing the old hitch, I loosely put one bolt (just a couple of turns) in the forward most hitch mounting hole on each side. Then I lifted the hitch and tied it loosely to each of these 2 bolts. Then I was able to maneuver the concealed part of the hitch behind the rear fascia, following the instructions on the etrailer video. After the hitch was in place, I opened the trunk and tied the 2" receiver just below the fascia loosey to the trunk latch. At this point the hitch was loosely suspended in position. I removed the tied up end and bolt from one side and screwed it loosely in place and then did the same for the other side. To finish up I inserted, tightened up and torqued all six bolts. This hitch has no place to attach the wiring plug, so you have to be creative there. All in all a great experience dealing with etrailer and a perfectly fitting, nearly invisible hitch.
Mahlen
9/22/2019
After a year this hitch is still working as expected. A greeat purchase.
by: John09/04/2023
2017 Toyota Sienna
Hole alignment on passenger side forward is off. Tried loosening all other bolts and moving towards passenger side to align bolt to no avail. What should have been a 2 person nuts and bolts job will now cost me $$$. Will never use Curt hitch again.
Jenny N.
9/7/2023
It sounds like that the side brackets are flexed out of alignment. I will have our Customer Service team reach out to you.
by: Al C.07/29/2019
2019 Toyota Sienna
Hitch was a perfect fit. Installation video was very helpful—much better than what came inside the box. Hitch installation only took an hour. Very happy with my purchase. Also installed wiring harness as seen in photo. That took a little longer as wiring installation video available was for 2018. 2019 had some slight changes behind panel and underneath the car—but was easy to improvise a solution. Thank you etrailer for the videos!!!
Al C.
7/29/2020
Hitch is solid! No issues. Used it for our Curt 5-bike rack and a 8’ x 4’ utility trailer. Great investment and reasonable cost—saved a bundle when you install yourself. Before you say you can’t do it, watch the etrailer videos...they will change your mind.
by: Steve 01/05/2024
This hitch fits great and does not protrude down causing ground clearance issues. Excellent piece of kit.
by: Michael 08/04/2022
This hitch has worked wonderfully! I didn't know how much I would actually use it, but it has been a lifesaver and hasn't let me down in the slightest
Michael
8/5/2023
The hitch still works perfectly. Havent had any issues whatsoever. Im glad I went with the less visible option, because when Im not using it, it seems to blend into the vehicle really well.
by: Aaron07/17/2023
2019 Toyota Sienna
I've used curt class 5 hitches on 2 silverados and they've worked well so i trust the brand. This class 3 seems sturdy and heavy duty enough for a minivan. I have yet to tow with it so the review is based mainly on the install experience.
Install was super easy. Did not need to remove the bumper. Just bottom plastic and the exhaust hanger. I bent two tabs out of the way and the reciever went in without a hitch ;)
Only tools used:
Utility knife
Flat head screw driver
3/8 ratchet with extension
10mm socket
19mm socket
Also don't trim the plastic as deep as the instructions say. Once the hitch is installed measure back from the plastic mount holes in the bumper to the back of the reciever tube. I think I only trimmed about a 4"×4.5" notch in the bottom plastic. Just used a Utility knife. No power tools needed as the panels is really soft and easy to cut.
by: Adam 10/04/2023
Fast shipping and great instructions on how to install from etrailer. The video was helpful and provided great helpful tips to make it easier to install. I'll be testing out the hitch this weekend and expect it to be great!
by: Aaron 05/06/2024
2020 Toyota Sienna
Fit absolutely perfect. Had the whole thing installed in about 40 minutes. Couldn't have asked for anything more.
by: Jonathan B.10/31/2019
Can’t complain about anything. I installed this hitch on my 2018 Toyota Sienna LE AWD with a friend. We required some tools (plastic pry tools, shears to cut plastic body panels, wrenches, jack and stands, etc.). The hitch keeps my Thule four bike rigidly attached. The only wiggle or slop I feel is in the rack and not the hitch.
by: M06/10/2021
Perfect fit. The installation instructions were very helpful and provided enough detail to prepare for the job and execute the job with no problems.
Since I did not have a lift, I used a cinder block and leftover pieces of 2x4 and hardwood flooring to prop up the receiver prior to installing the bolts. I used the shipping box to slide the equipment into position. The box also acted as a back cushion.
by: Evan10/02/2022
2013 Toyota Sienna
Fits great. It is best to install with a second person. I had a cut a small hole in the plastic rock guard. It looks really clean. I am glad I sent with this product instead of the ihaul version.
by: Keith05/10/2020
Since I was installing this solo in the driveway, I had to figure out a way to lift and get it into place. Using a large floor car jack with wheels and a long handle, I could maneuver and lift the device into place while I worked the bolts by hand. NOTE: not mentioned in the shee that came with it, was the need to bend two bolts out of the way for installation, and then bend the bolts back into place. These are the two closes the the back hitch location that you use a giant Philips screwdriver to remove the skid plate from. The cardboard box itself is great for sliding underneath the vehicle.
by: William08/03/2022
This hitch is great! I didn't want to see the whole assembly, so I went with the low profile unit. My vehicle looks like it came from the factory with it. I recommend 100%
by: Dain09/23/2020
2016 Toyota Sienna
Hitch went on easily in 59 minutes. (Tried to beat the expert time). Had tools set up ahead of time and a friend to help hold in place while fastening. I did not take the bumper piece off, and just slid the hitch up behind it as demonstrated in the video. The stickers Toyota used to protect the weld nuts worked great. There was no rust on the 4 year old sienna(2016) that has been driven through three Minnesota salty winters.
by: Paul06/01/2020
Watched the installation video on the website which was very helpful. They recommend loosening the exhaust and bending down two tabs holding the appearance panel. I was able to skip this with the help of my son. Total time was about one hour. I found the item to be heavy for one person. I used a floor jack to help hold it while I bolted it in. Shipping was fast even with a holiday and it was very well packaged. Straightforward installation. Receiver is high enough that it does not bottom when pulling into the driveway. Use it for a bike rack on road trips with no issues.
25
202
Show More Reviews
See what our Experts say about this CURT Trailer Hitch
- Trailer Hitch Recommendation for 2020 Toyota Sienna for Ground ClearanceTo avoid any issues with ground clearance with your 2020 Toyota Sienna, I strongly recommend a trailer hitch with a concealed crosstube because they will sit up higher and give you more ground clearance than a hitch with a visible crosstube. When we test fit the three trailer hitches that fit your 2020 Sienna that have a concealed crosstube - the etrailer.com Trailer Hitch Receiver # e98853, Curt Trailer Hitch Receiver # C13343, and Draw-Tite Trailer Hitch Receiver # 76112 - we found that...
view full answer...
- Is the Ultra-Fab Steel Roller # UF48-979020 Compatible with a Hitch Receiver for a 2011 Sienna XLEAlthough the Curt # C13105 and # C13343 as well as the Draw-Tite # 76112 are confirmed fits for your 2011 Toyota Sienna XLE, they are not compatible with the Ultra-Fab Steel Roller # UF48-979020 due to the safety chain loops. Out of the trailer hitch receivers that you referenced I recommend installing the Curt Trailer Hitch Receiver # C13343 because it installs up and under your rear trim. The only part of it that is visible is the actual hitch receiver opening and safety chain loops....
view full answer... - Recommended Towing Setup for 2018 Toyota SiennaOn your 2018 Toyota Sienna, the bumper does not get trimmed at all when installing the Curt Trailer Hitch Receiver # C13343. Only the underbody panel gets trimmed. I've attached a video to assist. The wiring harness needed depends on the trim model. If you have the SE trim then you will need the harness # 118498 , where all other models will use the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118648. You will need to run the 12V power wire to your battery, but...
view full answer... - Differences Between Curt and Draw-Tite Trailer Hitches for 2020 Toyota Sienna This is a great question and I can definitely understand being a bit overwhelmed trying to work through all the available hitch options for your vehicle. Just to cut right to it I specifically recommend the Curt Class III Trailer Hitch # C13343 for your 2020 Toyota Sienna and I will go through my reasoning below. Both Curt and Draw-Tite offer two different 2" trailer hitches for your 2020 Toyota Sienna and they can be easily categorized into hidden and non-hidden options. The Draw-Tite...
view full answer...
- Tools Needed to Install Curt C13343 Class III Trailer Hitch Receiver on 2013 Toyota SiennaI'd be happy to help with that. No worries, you got this! To install the Curt Class III # C13343 hitch on your 2013 Toyota Sienna, the following tools are suggested: • A ratchet with a 19mm and a 10mm socket • A standard flat screwdriver with a small blade • A 6 inch socket extension • Torque wrench as you mentioned • A rotary tool like a Dremel or tin snips • A permanent marker • Masking tape • Measuring tape or a ruler And possibly a battery terminal cleaning brush and WD-40 (more...
view full answer... - Parts Needed to Added Concealed Trailer Hitch and Redarc Brake Controller to 2018 Toyota SiennaOk, we can absolutely get your 2018 Toyota Sienna set up with a trailer hitch that has a hidden crosstube, as well as the wiring needed to add the Redarc brake controller. There are three parts you will need for sure, which are the hitch, brake controller, and 7-way installation kit: - Curt Trailer Hitch Receiver # C13343 - Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR - Universal Installation Kit for Trailer Brake Controller # ETBC7 You will need these three parts no matter...
view full answer... - Which Hitch Should I Install On My 2017 Toyota SiennaWhen it comes to installing a trailer hitch on your 2017 Toyota Sienna both the Draw-Tite and Curt hitches are close in comparison, but I recommend The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # C13343. The hitch is made in The USA. It has a gross towing weight up to 3,500 pounds and has tongue weight up to 525 pounds. Be sure to check your manual to see what the actual tow rating is for your vehicle. To grow your towing experience further I recommend The T-One Vehicle...
view full answer... - Difference Between Class III Trailer Hitches for 2020 Toyota SiennaSo there is one main difference between the Class III trailer hitches that fit your 2020 Toyota Sienna, and that's the visibility of the crosstube, with there being options for a concealed crosstube and a visible crosstube: Concealed Crosstube: - Draw-Tite Trailer Hitch Receiver # 76112 - Curt Trailer Hitch Receiver # C13343 - etrailer.com Trailer Hitch Receiver # e98853 Visible Crosstube: - Draw-Tite Trailer Hitch Receiver # 75237 - Curt Trailer Hitch Receiver # C13105 - etrailer.com...
view full answer...
- Hitch and 5-Bike Rack Recommendation for 2017 Toyota Sienna for Ground ClearanceThe best hitch for ground clearance that fits your 2017 Toyota Sienna is the Curt hitch part # C13343 which sits up higher and also only has the hitch opening that hangs down below the rear bumper which helps considerably with ground clearance when turning into a steep driveway. Then for a great 5-bike rack at a great price, take a look at the Curt Premium 5 Bike Rack for 2" Hitches - Tilting Item # C18065. I attached a review video for this rack on a similar 2014 Toyota Sienna. Since...
view full answer...
- Does Draw Tite or Curt Hitch for 2017 Toyota Sienna have Best Ground ClearanceWhen we installed the Curt hitch part # C13343 on a 2017 Toyota Sienna just like yours we found that from the top of the top of the hitch opening down to the ground measures 13 inches and then from the hitch pin hole out to the furthest point out on the bumper measures 4 inches. When we installed the Draw Tite hitch part # 76112 on a similar 2017 Sienna we found that from the top of the hitch opening down to the ground measured 12 inches and from the center of hitch pin hole out to the...
view full answer... - Best Concealed Trailer Hitch Fit for 2020 Toyota SiennaThere are three trailer hitches with a concealed crosstube that fit your 2020 Toyota Sienna that have a concealed crosstube, the Draw-Tite Trailer Hitch Receiver # 76112, Curt Trailer Hitch Receiver # C13343 and etrailer.com Trailer Hitch Receiver # E98853. Of the three I highly recommend the Draw-Tite # 76112 because of the company's strong reputation for quality and because this is the only hitch of the three that can be used with a weight distribution system, which is important if you...
view full answer... - Which Curt Trailer Hitch for 2017 Toyota Sienna is ConcealedFor your 2017 Toyota Sienna the Curt hitch part # C13343 is listed as a "concealed hitch". This means that most of the hitch isn't visible but the hitch opening where the ball mount slides into. This is as concealed as you are going to find. I attached a picture that shows where the rear area would most likely get trimmed. For a hitch that is not "concealed" Curt also has the part # C13105 which has the crosstube visible as well. If you asked for a concealed hitch and this is what they...
view full answer...
- Will Back Up Sensors on 2016 Toyota Sienna Need to Be Disabled When TowingActually, you really shouldn't need to do anything with the sensors because they'll only activate when the vehicle is in reverse. If you find that having them sound while your backing is annoying, you can install a switch such as # 37212595 inline with the power circuit feeding the sensors so you can turn them on and off as needed. You'll need to trace the sensor wires from the bumper, and locate which wire in their harness carries power. Install the leads for the switch inline on that...
view full answer... - Replacement Hitch Mounting Hardware for 2014 Toyota SiennaWe've got exactly what you need. You can order a replacement hardware kit for a hitch with part # RHK. You'll go to that part's page and put in the part number of the hitch you have for your 2014 Toyota Sienna (or any Curt or Draw-tite hitch that is compatible with your vehicle) in the box on the page and receive all of the mounting hardware required to get your hitch installed. For reference, the Curt # C13343 is a confirmed fit on your 2014 Sienna and can be used in the field marked...
view full answer... - Least Visible Trailer Hitch Recommendation for 2017 Toyota SiennaOf the 2 inch Curt hitches we offer for your 2017 Toyota Sienna the part # C13343 is the one to go with as it has only the hitch opening visible down below the bumper. The instructions do recommend removing the rear fascia to install the hitch. We sometimes find that there can be shortcuts made to install hitches but in general that is not the case. We currently don't have an install video for this hitch yet either.
view full answer... - Best Trailer Hitch for a 2016 Toyota SiennaActually the Draw-Tite # 76112, Curt # C13343, etrailer # e98853, and EcoHitch # 306-X7255 all install so that only the receiver is showing. A lot of people like this look instead of having a thick piece of steel underneath their vehicle as well. You are correct in choosing a Class III trailer hitch with a 2" receiver over a Class II trailer hitch with a 1-1/4" receiver. The reason being that they are stronger and they are compatible with many more accessories. For your application I recommend...
view full answer... - Will the GearSpace 34 Fit a 2020 Winnebago Vita 24P and a 2020 Toyota Sienna? The GearSpace 34 Enclosed Cargo Carrier for 2" Hitch - Slide Out - 34 cu ft - 300 lbs - Dark Gray # HGK819 is designed to fit a 2-inch hitch receiver on your 2020 Winnebago Vita 24P. I went ahead and called my contact at Let's Go Aero, and they confirmed that the weight capacity of 300 pounds remains the same even when the carrier extends to its full length. If you need a hitch recommendation for your 2020 Winnebago Vita 24P, I recommend the Curt Class 5 Universal Weld-on Hitch w/ Brackets...
view full answer... - Comparing etrailer, Curt and EcoHitch Hitch Receivers For Ground Clearance On a 2014 Toyota SiennaThe only difference in the etrailer Trailer Hitch Receiver # e98853 and Curt Trailer Hitch Receiver # C13343 is going to be the powder coat being matte black on the etrailer and gloss black on the Curt. As we have partnered with Curt to build our receivers in the matte black finish they are identical in dimensions. I do prefer the matte black powder coat on the etrailer receiver as it gives a more OEM appearance. As these both mount in the same position as the EcoHitch Hidden Trailer...
view full answer... - Recommended Trailer Hitch for 2019 Toyota Sienna for Ground ClearanceThe trailer hitch I recommend for your 2019 Toyota Sienna is the Draw-Tite Trailer Hitch # 76112 because if you plan on towing, this hitch is rated for weight distribution and the similar hitches are not. When we test fit the Draw-Tite Hitch # 76112, Curt Hitch # C13343, etrailer.com Hitch # E98853 and EcoHitch # 306-X7255 on a 2019 Toyota Sienna we found that each of them have 13 inches of ground clearance, and with the exception of the EcoHitch, have a 525 lb tongue weight capacity (the...
view full answer...
- How To Prevent Exhaust Contacting Draw-Tite 76112 On 2020 Toyota SiennaYou are correct that some customers have mentioned that the exhaust on their 2020 Toyota Sienna was contacting the Draw-Tite Trailer Hitch Receiver # 76112, but there have been plenty of customers who have installed this hitch without any issues. The Draw-Tite # 76112 and Curt # C13343 you were looking at have nearly the exact same design so either hitch could have the noise. If you notice the exhaust hitting the hitch you can bend the hanger slightly away from the hitch for some extra...
view full answer... - Concealed Trailer Hitch With Maximum Ground Clearance/Trailer Wiring Harness for 2020 Toyota SiennaI'd be happy to help with that. Let's begin with the hitch. For the most concealment/ground clearance I'd recommend the Curt class III hitch, part # C13343. This hitch will be mostly concealed, with the crossbar being hidden behind the bumper/fascia. The only visible portion of the hitch will be the receiver tube and the safety chain loops. For a 4-pole trailer wiring harness, I'd recommend the Tekonsha # 118648. You'll also need a ball mount. The average leveled height of a trailer...
view full answer...
- Trailer Hitch Recommendation for 2016 Toyota Sienna for Use With Yakima Fullswing Bike RackFor your 2016 Toyota Sienna the Draw Tite hitch part # 75237 is a confirmed fit and would easily have enough clearance to allow your Yakima Fullswing 4 part # Y02465 to install and function like normal. This hitch has a distance of 4-1/2 inches from the center of it's hitch pin hole out to the furthest point out on the rear bumper. The Fullswing has 9-1/2 inches from it's hitch pin to the base of the rack.
view full answer... - Recommended Trailer Wiring Harness for 2020 Toyota SiennaThe trailer wiring harness option I recommend for a 2020 Toyota Sienna is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, part # 118648 or part # 118498 for SE models. This harness is a direct plug-in-play option with no splicing required. It has a 4-way/4-pole flat connector which is the most commonly used. If you don't already have a trailer hitch, I recommend the Curt Trailer Hitch Receiver part # C13343.
view full answer... - Recommended Hitch for a 2024 Toyota Sienna No chance but congrats on the new vehicle! The Curt Hitch item # C22UR that fits your 2024 Toyota Sienna was designed for the 4th generation Sienna's when they went to the all hybrid models that started with the 2021 model year. The 2013 Sienna was the 3rd generation so there's no hitches from it like your Curt item # C13343 that will fit the newer models. The frame width and the height of the hitch are completely different. The Curt Hitch item # C22UR is custom fit and bolts to your...
view full answer...
Do you have a question about this Trailer Hitch?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Edited by:
Lindsey S
Video by:
Joshua S
Video by:
Dustin K
Video by:
Michael B
Video Edited:
Jacob T
Video Edited:
Kathleen M
Video Edited:
John S
Updated by:
Wilson B
Updated by:
Ronnie R
Updated by:
Kristina F
Updated by:
Isabelle B
Written by:
Amanda M
Test Fit:
Shane H
Test Fit:
Robert C
Test Fit:
David F
Test Fit:
Ryan G
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Marty S.
7/23/2023
Working great and you hardly notice it.