How To Prevent Exhaust Contacting Draw-Tite 76112 On 2020 Toyota Sienna
Question:
HI... I am looking at both the Draw-Tite and Curt hitches that conceal under the rear cover. I have seen comments customers that purchased the Draw-Tite model, and they complained of some noise caused by the exhaust hitting the hitch. There is apparently a workaround/fix to move the exhaust to fix the issue with the Draw-Tite, but does the design of the Curt prevent this noise occurring?
asked by: Andy N
Expert Reply:
You are correct that some customers have mentioned that the exhaust on their 2020 Toyota Sienna was contacting the Draw-Tite Trailer Hitch Receiver # 76112, but there have been plenty of customers who have installed this hitch without any issues.
The Draw-Tite # 76112 and Curt # C13343 you were looking at have nearly the exact same design so either hitch could have the noise.
If you notice the exhaust hitting the hitch you can bend the hanger slightly away from the hitch for some extra clearance.
Between the two hitches I recommend going with the Curt # C13343 as we have found that the powder coat finish Curt uses is the strongest and more resistant to chipping and scratching.
I included videos for both of the products mentioned for you to take a look at.
Products Referenced in This Question
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 3500 lbs WD GTW
- 2 Inch Hitch
- 525 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Replacement Storage Bin for Lippert Underchassis Storage System - Qty 1
- Shop: Plastic Storage Trunk for Malone MegaSport Kayak Trailer - 8 cu ft
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: UWS Large Tote Storage Box - 1.3 cu ft - Bright Aluminum
- Shop: UWS 48" Standard Chest for UWS Hitch Cargo Carrier - 11.1 cu ft - Bright Aluminum
- Video: Curt Trailer Hitch Installation - 2017 Toyota Sienna
- Video: Curt Trailer Hitch Installation - 2019 Toyota Sienna
- Search Results: aluminum hitch cargo carrier
- Shop: Roof Rack
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 44649
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Shop: Brake Controller
- Search Results: 68149
- Article: Trailer Wiring Diagrams
- Shop: Fifth Wheel Hitch
- Search Results: 25580
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Search Results: dust cap
- Video: etrailer Hitch Pin Alignment Collar Review
- Shop: Suspension Enhancement