It sounds like you're trying to replace the battery isolator solenoid. This is what allows the starting battery on your 2018 Jayco Precept Prestige to charge the house batteries when the engine is running, but keeps the house batteries from draining the starting battery when the engine is not running.
For a replacement you'd need the Deka # DW08771.
If you mean some other kind of solenoid just let me know what it's doing, but this should be the only solenoid you have. view full answer...
For your 2010 Jayco Jay Flight 23FB the correct hub/drum is the part # 84557UC3-EZ which is a 3,500 lb axle hub/drum with a 5 on 5-1/2 inch bolt pattern. This comes with bearings and seals but if you wanted them separately you'd want the bearing kit # BK2-100.
For brake assemblies you'd want the part # 23-468-469. view full answer...
It appears the part number you have listed may be a Marshal brand, we do not carry this brand but do have high quality components available from MB Sturgis. The length of hose needed, thread size and type are required to ensure a proper fit for replacement. We have the MB Sturgis, # 100473-12, a 12" hose with the needed Type 1 - Male on one end of the pig tail and a 1/4 Inch - Male NPT on the other. See the attached product review video. We also have the same hose but in a 15" length... view full answer...
It sounds like you have a 2005 Jayco Jay Flight 31BHS which has a GVWR of 6,935 lbs. Assuming that is correct, it is likely you have 3,500 lb axles on your trailer. I recommend verifying this information by checking the axle tags to be sure.
If that is the case, you can use the Electric Trailer Brake Kit # AKEBRK-35-SA. These are 10" x 2-1/4" brake assemblies with a 4 bolt brake mounting flange pattern and a 3,500 lb axle rating. If you need mounting hardware we have the # BRKH10B.
Since... view full answer...
Yes, the Lippert Heavy-Duty Replacement Shock # LC283280 will fit your 2022 Jayco Eagle 321RSTS. We have had this question come up in the past in relation to the Jayco Eagle 321RSTS and we have been able to verify that they do fit. view full answer...
For an 18 foot Carefree electric awning, you do have the right part with the Solera Family Room for 18' RV Awning # LC362233.
There are no other parts you need to purchase in order to install it, but you will need some very basic tools for the installation. According to the instructions - which I have linked for you - the tools needed are simply a cordless drill, mallet/hammer, 1/4” hex head bit, measuring tape, sealant, and ladder. Once you have all that you're all set! view full answer...
The Furrion part # C-FACR15SA-A01 comes with everything needed for your Furrion 15k btu unit part # FR86PR to connect to and be operated with your current Coleman air distribution box and thermostat. You would not need to also get the zone controller either. view full answer...
The Adco SFS AquaShed Cover part # 290-52238 and Adco Polypropylene Storage Lot Cover part # 290-74838 are both great options for a 2017 Jayco Jay Flight SLX 145RB. The Polypropylene is more heavy duty so it should last longer but it will also be more difficult to take on and off so it really just comes down to how long the trailer will be in storage and how many times you'll need to install and remove the cover. view full answer...
The Lippert High-Speed Power Stabilizer Jack # LC298707 would not be able to mount to your frame since you only have 68-1/4" from outside to outside edge and this stabilizer requires a 68-11/16" spacing. Instead I recommend installing the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705 since they are adjustable to fit frame widths from 40" to 80".
The # UF39-941705 also has a major advantage over the # LC298707 since has lifting/leveling capabilities, whereas... view full answer...
In regards to the Equal-i-zer Weight Distribution System part # EQ37140ET, yes the springs bars should have tension under load. This is a pretty heavy duty system so odds are there is just more tension than you're used to. The angle set bolt should not be loose, it should be tightened until the spacer rivet is firmly against the shank per the instructions.
If you are concerned with how the system is setup, just take it back to the dealer that installed it so they can fix any issues. view full answer...
The confirmed replacement for a Coleman Mach 8335-8915 AC Unit Shroud is the MaxxAir Replacement RV Air Conditioner Cover - Coleman-Mach / RVP Brand RV Air Conditioners - White Item # MA8335A5261. view full answer...
For your 2021 Jayco Jay Feather Travel Trailer I recommend the CLUB Tire Claw XL - Wheel Lock product # WI491KA
You can lock these around your wheels to prevent anyone from being able to drive off with your camper and the rubber on them will prevent any marring on your rims. I've attached a video with additional information and a quick how to use guide for you as well. view full answer...
Hey Scott, since we know your 2012 Jayco Eagle Super Lite HT 26.5RLS has 12 inch brake assemblies the best solution for a replacement would be the etrailer part # AKEBRK-7-SA which we know fit and work great. These are self adjusting too which means you would not have to worry about ever having to manually adjust them. view full answer...
Hi Marty; to answer your question, the SnapPad SnapJack SJ for RV Scissor Jack Stabilizers # SN65FR will work for your 9,200 lb trailer, yes.
The specs aren't actually for the SnapPads themselves (which I know is a bit confusing). The # SN65FR will fit scissor jacks that have individual capacities for 5,000 lbs to 7,000 lbs. For example these will fit the Lippert Scissor Stabilizer Jacks # LC285344 which have a 5,000 lb per-jack capacity. view full answer...
The MORryde pin box you have on your trailer now is compatible with the Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter part # AM3200 so you would not need to change anything. view full answer...
Thank you for your purchase from etrailer of the Furrion Vision S Camera System # FOS05TASF.
According to Furrion there are a number of things you can do to try to remedy the situation if you are not getting a signal, to start you should check if the camera antenna is fitted and secured correctly, as it should be vertical. It could also be that the distance between camera and monitor is too great so if possible reduce that distance. There may be interference from electrical appliances... view full answer...
We do not have a slam latch (matching or not) that fits in the door cut out of the Global Link lock that you currently have. Depending on the thickness of the compartment door you may be able to install a Global Link # 295-000014 thumb turn cam latch. If you need a different size just email me back with your door thickness. view full answer...
Since your 2021 Jayco Eagle HT has 4 landing gear legs that have feet that are 9 inches in diameter the SnapPads you'd want are the # SP54FR4. view full answer...
What you have there are the Command 003-20 incandescent tail lights. Although we do not have the incandescent replacement, we do have the LED version which is the # CE86FR. You will want to keep the lights the same way they are now with the brake light on the outer and the white light on the inner. These do not have a designation for driver or passenger side so all you need to do is flip it around to the correct orientation when you mount it. view full answer...