The Solera 18V Power RV Awning Conversion Kit - Universal - 69" Arms - Black # LC434729 that you were looking at will only fit your Carefree awning if you have at least 2-1/2 inches (not feet) between the awning rail and top of door, and also 69" of unobstructed area from awning rail straight down.
This kit is for 18V, but if you need 12V then go with Solera 12V Power RV Awning Conversion Kit - Universal - 69" Arms - Black # LC434723. view full answer...
Yes, the Equal-i-zer Weight Distribution System # EQ37140ET can be used with an underslung trailer hitch. The link plate for the Sway-Control Bracket # EQ95-01-5600 will be inverted to lower the bracket and compensate for the underslung design.
You will need a 1-7/8" 12pt Thin Walled Socket # ALL643216 to install the included 2-5/16" hitch ball that comes with the Equal-i-zer system. view full answer...
In regards to choosing between the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling Systems part # LC358590 and part # LC675817, you'll need to measure. The rear jack brackets should be installed approximately 1' behind the rear axle anger. If there will be 20' or less between the center of the landing gear footpad and the center of the rear jack footpad then use the 4-point part # LC358590. If your setup requires more than 20' between the jacks, use the 6-point part # LC675817.
If... view full answer...
For a trailer hitch receiver that will fit a 70-1/8 inch frame like you have on your Jayco Jay Flight you will need a hitch from Curt which fits frames that range from 22" to 72" wide:
- Adjustable Width Trailer Hitch Receiver for RVs # 13703 view full answer...
A 4-wire phone cable is not something that we are aware can be used instead of the Replacement Control Cable for MaxxAir MaxxFan Plus Roof Vent Wall Control Panel # MA69FR.
This is what you would need as opposed to a phone cable for models 00-04500K, 00-04700K, 00-04800K, 00-04900K, 00-07000K, 00-07500K, 00-08500K, 00-08700K, and 00-08900K. view full answer...
The correct way to measure for a slide out awning is to measure from the outside end of the flange to the outside edge of the other flange. Generally we also like to have about 5-7" of clearance on each side of the slide out for clearance so that the arms of the awning don't come into contact with anything when retracting the slide out. If you have less than this amount of clearance on any of the slides then let me know and we can find the correct fit for you.
74" Slide Out # LCV000168105... view full answer...
Unfortunately we do not carry the motor for the Northern Breeze model so I recommend replacing it with the Ventline Ventadome Trailer Roof Vent w/ 12V Fan # V2094SP-34. This roof vent uses a 12-volt fan to circulate air in motor homes and enclosed trailers, keeping interiors ventilated without compromising security. view full answer...
While the Andersen Rapid Jack # AM3620 would work for what you are wanting I recommend going with the Stromberg Carlson Base Pad RV Levelers # SC76MR instead. These have a wedge that will help hole the front wheel in place. view full answer...
Yes, you can use the MORryde Cushioned 5th Wheel Pin Box, # MR52VR with an Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter, # AM3200. view full answer...
Since your 2014 Jayco Jay Feather Ultra Lite Travel Trailer should weigh around 3,500-4,500lbs I recommend the Ultra-Fab Electric A-Frame Jack - 18" Lift - 3,500lbs # UF38-944017. This jack extends 6" in 25.3 seconds at 1,000lbs of tongue weight, to give you a bit of a speed reference. At max weight your trailer would at most have 450lbs of tongue weight.
It has an easy bolt-on or weld-on installation for A-frame trailers, hardware not included, with the distance between the mounting... view full answer...
If your brake shoes# bp04-065 are 10" x 1-1/2" you will need these brake springs # K71-362-00. The springs you were looking at # BP06-120 were for 2-1/4" shoe width. view full answer...
When the Lippert # LC791572 steps are properly installed with the threshold plate firmly against the outside threshold you should have no issues. The only thing we hear from customers is how much they love them!
While you have your tools out you might as well take down those old stock rattle-trap steps that came stock on your trailer and install the Lippert # LC664640 locking steel box just made to fit in the spot where the steps were. Great spot for black water supplies, or roadside... view full answer...
Yes it does! The correct hub and drum for your 2012 Jayco Jay Feather Ultra Lite X17Z Travel Trailer is the Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles # 84557UC3-EZ.
Along with this hub, for grease I recommend the Prime Guard Wheel Bearing Hi-Temp Red Grease # L11380; for a bearing packer I recommend the Bearing Packer # PTW1218 or # ALL647646. view full answer...
The modern equivalent of a 20.5 x 8 - 10 tire is a 205/65-10 tire. These two tires are going to have the exact same diameter of 20.5" therefore, you can absolutely use the 20.5 x 8 - 10 tires you have now as a spare. For a 205/65-10 tire, I recommend the Loadstar (Kenda) K399 Bias Trailer Tire part # AM1HP56. This tire has a bias ply, load range E (1,650 lbs) and speed rating N (87 mph). It also comes with a 2-year warranty.
I have attached a review video of the tire in addition to our... view full answer...
So long as your 2005 Jayco has tandem #12 Dexter Torflex axles that are mounted on the side you can use the Torflex Lift Kit - Tandem Axle # K71-725-02.
We don't have any way of knowing what is on your trailer but if you take a quick peek at the axle you should see a sticker on the beam that has the axle number, and if it says #12 and your axles have a 5,500 lb to 7,000 lb capacity each, you can use this kit. If you find you have a different axle you can use one of the following kits:
-... view full answer...
The Global Link RV Entry Door Locking Latch Kit # 295-000019 will fit your door if the cutout hole is 2-1/2" wide x 3-1/2" tall to 3" wide x 4" tall. Manufacturers do not list the door handles they use so the only way to replace them is to have the brand and serial number of the door handle to look up the exact size or just take it off and measuring the cutout hole to find a compatible fit. view full answer...
You definitely will not need to replace your axle to upgrade to a disc brake kit, like the Kodiak Disc Brake Kit - 13" Hub/Rotor - 8 on 6-1/2 - Raw Finish - 7,000 lbs # K2HR79. However, you will need to verify a few things before purchasing to make sure they will fit properly, specifically the inner and outer bearings.
This can be done 2 ways. The first, and the easiest, can be done by contacting Jayco and asking them which inner and outer bearings are used on your model. All you will... view full answer...
The best option we offer for a pre-mounted 205/75-14 trailer tire with steel wheel is the Karrier ST205/75R14 Radial Trailer Tire w/ 14" White Spoke Wheel part # AM32161. This is a ready to go setup with radial tires, steel wheels, and included valve stem. The tire has an 81 mph rating and the tires can handle up to 2,200 lbs each. You'll need to inflate them to 75 psi.
The Karrier ST205/75R14 Radial Trailer Tire w/ 14" White Spoke Wheel is made overseas, we don't have any domestic options... view full answer...
Those are good questions and there is one option for floor mats that fits the vinyl flooring of your 2022 Jayco Prestige 29MPV motorhome on a Ford E-450 chassis, which is from WeatherTech:
- WeatherTech Front Auto Floor Mats # WT26DV
These WeatherTech are the FloorLiner series, as the All-Weather type won't fit with vinyl flooring, and neither will the Husky option. The WeatherTech # WT26DV do work with vinyl flooring because they come with sticky 3M adhesive retention grommets that bond... view full answer...
The standard clearance requirement for the MORryde StepAbove RV steps like part # MR88RR is 3/8 of an inch which is the same for the # MR28RR. view full answer...
Go To Results