Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 10 Diodes - Round - Red Lens

See what our Experts say about this Optronics Trailer Lights

• What is Amp/Hour Rating of Optronics LED Trailer Tail Light # STL42RB
  Yes, the amp rating of the Optronics LED Trailer Tail Light # STL42RB being .413 amps is the amp/hour rating. That means that it would draw that much amperage over the course of an hour if that circuit was used.
  view full answer...
• Trailer Light And Mounting Bracket Recommendation
  The Optronics light, part # STL42RB, you are asking about uses the mounting holes in the included flange for mounting. This light features 10 Super LED lights and has a sealed, waterproof housing and lens kit. The mounting holes in the flange are spaced 4-1/4 inches apart center-to-center. We do have a mounting bracket, part # BK45BB, for a 4 inch light but the mounting holes are spaced 4 inches center-to-center. If you wished to drill the holes in the bracket to match the holes in the...
  view full answer...
• Parts Needed to Install Optronics LED Lights on Custom Bumper on 2012 Toyota Tacoma
  Both of the Optronics LED stop/turn/tail lights you referenced, parts # STL72RB and # STL42RB, use a 3-prong connector, either straight plug # A45PB or right-angle plug # A47PB. These fit the receptacles on the back of the light housings and provide 10-inch pigtails leads for connection. For a plug-n-play 4-pole harness to power the lights you can use the Tekonsha kit # 118496 which connects at the Tacoma's taillights with custom-fit connectors. You'll then cut off the 4-pole plug and...
  view full answer...
• Need Amber Taillights Like the Sealed 4" Round LED Trailer Taillight # STL42RB
  When it comes to the Sealed 4" Round LED Trailer Taillights, # STL42RB, the amber version is part # STL42AB. I have included two short videos for you.
  view full answer...
• Availability of 2 Inch Round LED Tail Lights for Trailer
  The closest match we have to the 2 inch stop/turn/tail lights you referenced are 4 inch round LED tail lights with grommet mount, # STL42RB. This is a 4 inch round clear back up light that has an overall diameter of 5-3/4 inches and a depth of 1-5/8 inches. This light will require a standard 3 prong plug, # A45PB. At this time we do not have any 2 inch stop/turn/tail lights.
  view full answer...
• Is Optronics LED Trailer Tail Light # STL42RB Sold Individually or In Pairs
  The Optronics LED Trailer Tail Light # STL42RB is sold individually. If you needed a pair you'd need to order a quantity of two of these. For a wiring harness you'd then need the part # A47PB and for a mounting bracket part # BK45BB and you'd be set.
  view full answer...
• Can Silverado with Separate Turn Signal Circuits be Wired to Taillights that are Combined
  We have taillight converters like the # RM-732 which will take a separate circuit setup like your Silverado has and combine them so that you can use the circuits on the lighting you have now that was designed for combined circuits.
  view full answer...
• What Size Hole Needs to Be Cut To Install the Sealed 4 inch Diameter Optronics Light STL42RB
  To install the Sealed, 4" Round LED Trailer Stop, Turn and Tail Light, Flange Mount Light # STL42RB that you referenced you will need to drill a 4-1/2 inch hole for the light to fit and the mounting holes will be 4-1/4 inches apart on center. For a pig tail harness you will want the part # A45PB.
  view full answer...
• Do Trailer Lights Sometimes Ground Through Mounting Hardware
  There are quite a few trailer light assemblies that use the mounting bracket as the ground. This works because the mounting brackets typically get attached to metal surfaces that touch the trailer frame which is where the ground strap of the trailer wiring harness connects. You can run a jumper wire from the mounting hardware to the main ground wire of the trailer if you wanted to as well.
  view full answer...
• Can Utility Lights in Trailer Run Off Running Light Circuit Through a Switch on an Aluminum Trailer
  Yes, you can run the switch power wire to a clearance light but the trailer would have to be connected to the vehicle with the running lights on for the interior lights to have power. Aluminum does not offer the best ground so if the lights do not work you may have to run a jumper ground wire to a steel component or the main trailer connector ground. I would try it first to see if there is any problem with grounding to the aluminum surface. A fuse is not needed though you could add one...
  view full answer...
• Replacement Taillights, Wiring and 7-Way Connector for Car Hauler
  To fit the round 4-1/2 inch holes on your trailer for the rear brake lights you could use the # STL42RB as this will fit in that hole. For a pigtail harness you would also need # A45PB. For the side clearance lights you would need to enlarge the holes to 3 inch in diameter, use the # A55GB as a grommet and then use # MCL59AB for the lights and # A46PB as a wiring harness. For a replacement 7-way with 8 feet of wire for running new wire everywhere you would want the part # H20046. You...
  view full answer...
  
• Pigtail for Optronics #42 Series Trailer Lights
  The Optronics LED Trailer Tail Light # STL42RB comes with the light assembly only, but we do have the following pigtail styles to choose from: - Right Angle 3-Wire Pigtail # A47PB - Straight 3-Wire Pigtail # A45PB
  view full answer...
• Round LED Trailer Tail Lights to Replace Peterson Incandescent Lights
  Three inches is small for a tail light. There aren't even any incandescent stop, tail, and turn lights as small as 3 inches. It looks like to get what you want you will need to got to a 4 inch light. If you like the Peterson lights and need a flush mount that mounts in a grommet you could use # 435800. It does use the plug-in style connector but you would still hardwire all of the wires, including the grounds, to the trailer. This light includes the grommet and pigtail. I have included...
  view full answer...
• Will Optronics Trailer Tail Light # STL42RB Fit a 1974 Blair Horse Trailer
  I went out to the warehouse and pulled an Optronics tail light, # STL42RB to measure the back to determine the size hole you would need. The trailer would need, or you would need to cut, a 4-1/2 inch diameter hole. The lights will fit the 4-5/8 inch mounting hole. You would also need a pig tail harness # A45PB.
  view full answer...
• Could Use a Trailer Light Mounting Bracket with a Sealed 4 Inch LED Stop Light
  Yes, I went out into our warehouse and pulled a Sealed, 4 inch Round LED Trailer Stop # STL42RB and a Trailer Light Mounting Bracket # BK45BB and found that they work together very well. All of the mounting holes from the # STL42RB line up with the # BK45BB. You would need bolts that have a diameter of no more than 3/16 of an inch to attach the light to the bracket. I attached a picture to the right that shows how these products would look if installed together. You might also be interested...
  view full answer...
  
• Replacement Tail Light For Forest River Georgetown XL RV
  I'd be happy to assist you. It sounds like you need the Sealed, Flush Mount Tall Rectangle LED Trailer Stop, Turn and Tail Light, Grommet and Plug, 12 Diode # STL34RB but most of the pictures I see have round tail lights like the Sealed, 4" Round, LED Stop/Turn/Tail light, 21 Diode - Red # STL55RB. If this is not the correct part, then send me a photo with the measurements of the light and we will get you what you need. The numbers and letters that are actually printed on the light are...
  view full answer...
  
• Replacement LED Tail Light For Pacific Trailer
  We have LED trailer lights available. If you have the dimensions of the light you want to replace that would help in finding the right replacement for your Pacific trailer. From my research I found that some of the Pacific trailers use part # STL42RB. This is a 4-inch round flange mount light that has 10 LEDs. It is a three function stop/turn/tail light. If you need a flush-mount light, we also have part # STL43RB. this is also a 3-function 10-LED light. If you are looking for an oval...
  view full answer...
• Turn Signal and Brake Lights Stop Working on Trailer When Headlights are On
  This sounds like a ground issue. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light. Make sure that the vehicle side and trailer side connectors are clean and free of corrosion inside and out. The main connector grounds should be attached to clean and corrosion free bare metal surfaces. The light grounds should also be attached to clean and corrosion free bare...
  view full answer...
• Replacement LED Trailer Light to Reduce Power Draw
  The Optronics LED Trailer Light # STL42RB is not what I could call an exact replacement for the # ST40RB but for all purposes it will be what you're looking for. The # STL42RB is 1/8 inches larger in diameter and 3/8 inches deeper so at the most you may need to do a little filing to the opening for the light in your trailer to install it. The mounting flange is metal. There is also a Stainless Steel Trim Ring # A5TRSSB available. It does not include a gasket, however If you would prefer...
  view full answer...
• Backup Lights Similar To the Optronics 4 Inch Round LED Trailer Light # STL42RB
  The closest backup light that we carry to the 4 Inch Round LED Trailer Light, # STL42RB, is the 4 Inch Round LED Backup Light, # BUL11CBX. This is a 4 inch round clear back up light that has an overall diameter of 5-3/4 inches and a depth of 1-5/8 inches. This light will require a standard 2 prong plug, # A45CB, and has a reflector on the mounting flange.
  view full answer...
• How to Ground a Trailer LED Light that Only has 1 Wire
  If a light has just 1 wire that means that it grounds through its mounting hardware. Be sure to use steel hardware and mount the light to a clean and corrosion free bare metal surface. If there isn't a steel surface where you want to mount the light you can place a ring terminal with attached wire between the hardware and mounting surface and attach the other end of the wire to a steel surface.
  view full answer...
• How Does a Trailer Light Mount in the Buyers Products Light Box 337LB663
  The Buyers Products Tail Light Mounting Box - 4" Round Hole # 337LB663 is designed to be used with something like the Rubber Grommet for 4" Round Trailer Lights # A45GB and Optronics LED Trailer Tail Light - Stop, Tail, Turn - Submersible # STL55RB. The light will snap into the grommet, which will then snap into the mounting box. The wires of the 3-Wire Pigtail for Optronics Trailer Lights # A45PB will need to be run through the small hole that is drilled into the box, but this can be a...
  view full answer...
• Converter Recommendation to Install Combined Taillights on a Flatbed Truck that had Separate Bulbs
  It sounds like you need to convert the separate wiring of your 1991 Nissan truck to a combined setup to work with the Round LED Taillight # STL42RB. For this you will need to get a Roadmaster Brite-Lite Wiring Converter # RM-732. You will run the wires from your vehicle to the right side of the # RM-732 by function, and then from the left side of the box you will run the corresponding left or right turn signal wire to the red wire of the # STL42RB. The tail light circuit will bypass this...
  view full answer...
• Replacement Option For Glo-Brite 9891-88 LED Trailer Tail Light
  We do have an option for you to replace your Glo-Brite 9891-88 LED trailer tail light. Based on my research this is a 4 inch round LED tail light that uses a 3-wire plug and fits in a 5-1/2 inch grommet. We have exactly that with the following light: - Optronics LED Trailer Tail Light # STL42RB This comes with the grommet, which has mounting holes separated on center by 4-1/4 inches, so the only other thing you will need is the 3-wire pigtail, and you can choose from a standard or right...
  view full answer...

Do you have a question about this Trailer Light?