Right Angle 2-Wire Pigtail for Optronics Trailer Lights - 2-Prong PL-10 Plug - 6" Lead

See what our Experts say about this Optronics Accessories and Parts

• Recommended Round Trailer Marker Lights to Fit in 2-3/4 Mounting Hole
  The # MC56RB you were looking at is designed to fit in a 2-3/4" diameter hole and will have mounting holes 2-11/16" apart, so these will work for your 2011 PJ Dumper trailer. If you also need new pigtails for the wiring, you can use the # A86PB or the # A46PB (right angle pigtail). I've linked some review videos of these parts for you to have a look at.
  view full answer...
• Replacement Rear Trailer Marker Lights For A 2-3/4" Cutout Hole
  For a 2-3/4" cutout hole we currently only have two options, the Optronics # A56GB (closed back) and # A57GB (open back). These grommets are compatible with lights like the Optronics # MCL57RB or # OPT94FR. You'll need a 2-pin wire harness # A46PB to connect the lights to your trailer's wiring.
  view full answer...
• 2-1/2 Inch Amber Clearance Light Recommendation for Trailer
  For an amber clearance light that is 2-1/2 inches in diameter that uses a grommet for installation you would want the part # MC57AB. For a grommet you would want the part # A55GB and then for a pigtail part # A46PB.
  view full answer...
• Will the Optronics License Plate Light # LP97CB Work on a 2000 Featherlite Car Hauler
  In order to determine if this Sealed, Ear Mount Trailer License Plate Light # LP97CB that you referenced would be the correct replacement license plate light you will need to compare the mounting hole dimensions to that of your current setup and see if it would bolt up. This light has a distance of 2-3/4 inches between the mounting holes. If you find that is the same as your current setup this product should work for you. You might also be interested in purchasing a Two Wire Pigtail 3...
  view full answer...
• Are the Optronics Uni-Lite Mini LED Clearance Lights DOT Rated as a Reflector
  The Uni-Lite Mini LED Side Marker and Clearance Lights, like part # MCL11AKB and # MCL11RKB, are not rated as reflectors. We do have a couple of options that you might consider. Check out the 2-1/2 inch Round LED Trailer Clearance, Side Marker Light with Reflector, # MCL59AB and # MCL59RB. I added links to the parts needed to complete the installation of these lights for you.
  view full answer...
• Replacement Light Options For An Older Rack And Roll Trailer
  The light of the Replacement Side Marker Light for Yakima Rack and Roll Trailer # 8880185 is 2-1/2" at the base so you would need a 2-1/2" hole in order for the light to fit. The grommet extends out past 2-1/2". You can try using a 2" round light like part # MC52RB (along with the wire harness # A46PB) or drill the hole larger to accommodate the # 8880185.
  view full answer...
• Do You Have The Optronics Mini LED # MCL14RB With a Plug Style Connector?
  The Thinline LED Trailer Clearance # MCL66RPG is the closest light we have to the Mini LED # MCL14RB with any kind of connector on the end. As you most likely have the Male 2-Wire Plug # A46PB on your trailer you can wire the Mini LED # MCL14RB with the Female 2-Wire Plug # 153-49 so that you will still be able to use the plug connectors. If you have a different style plug connector please let me know which style connector you have and I can see what is available.
  view full answer...
• Waterproof License Plate Light for Eagle Spirit Boat Trailer
  Thank you for providing the reference numbers from the license plate light on your Eagle Spirit boat trailer. In my research I was not able to find any cross-reference to these parts, nor was I able to verify the brand of lights originally installed by the trailer manufacturer. However, of all the submersible license plate lights we offer, the unit you referenced, Optronics Trailer Light # LP91CB, is the only one that is this 2-1/2 L x 1-3/16 W x 7/8-inch D size. It uses a 2-prong pigtail...
  view full answer...
• Does it Matter Which Way Wiring Harness is Plugged Into Optronics Marker Light MC-53RB
  Some lights are polarity sensitive but Optronics light # MC53RB is not. You should be just fine plugging in the wiring harness, # A46PB, either way.
  view full answer...
• Wiring Pigtail and Mounting Bracket Options For Installing Thinline LED Clearance And Marker Lights
  The Thinline LED Clearance and Side Marker Light # AL91AB require certain mounting brackets and plugs that are either already installed on the trailer or are available separately. A Right Angle 2-Wire Pigtail # A46PB will work with the Grommet # A91GB if you are looking to recess the light. Or Mount Brackets # A91OB and # A91BOB if you want to mount them on a surface with the wiring running behind the bracket. The Plug - Single Wire # A91LW is used for Mounting Brackets # A91BB and...
  view full answer...
• Availability of a Downward Projecting Submersible License Plate Lamp for a Boat Trailer
  The license plate lamp you referenced, part # UL94CB would project the light outward. If you were looking for a lamp that would mount above the plate that would shine downward, I would recommend the Optronics Sealed Rectangular Mini License Plate Light, part # LP91CB. If used along with the Trailer License Plate Bracket, part # LP25SB and the Two Wire Pigtail, part # A46PB, you will have a submersible license plate lamp that projects downward.
  view full answer...
• Trailer Clearance Light Part # A91RB Installation
  To connect the Optronics Red Mini Rectangular Trailer Clearance and Side Marker Light to your existing trailer wiring, you would need the pigtail which is part # A91LW if you were using the self grounding mounting bracket, part # A91BB. If you were using some sort of other bracket that is not self grounding, a two wire pigtail is offered, part # A46PB.
  view full answer...
• LED Clearance or Side Marker Trailer Light in Red
  For a complete set in red we have the Optronics LED Clearance or Side Marker Trailer Light - Submersible - 5 Diodes - Round - Red Lens item # MCL52RMB. If you are wanting an exact set up like the Optronics Miro-Flex LED Clearance or Side Marker Light w/ Grommet and Pigtail - Submersible - 3 Diodes - Amber item # MCL51CAK you referenced you will need the following parts: LED Clearance or Side Marker Trailer Light - Submersible - 3 Diodes - Round - Clear Lens item # MCL57RCB Right Angle...
  view full answer...
• Clearance and Side Marker Light With Clear Lens and Red LEDs
  We do carry a number of options for clearance lights that have a clear lens and red LEDs, but the red equivalent of the Thinline LED Mini Clearance and Side Marker Light - Clear Lens - Amber # AL91CAB has a red lens as opposed to a clear lens; it is the Thinline LED Clearance and Side Marker Light # AL91RB. If you want to go this route you can mount it with Grommet # A91GB (recessed mount) or Mounting Bracket # A91BOB (surface mount) with Right Angle 2-Wire Pigtail # A46PB. For similar...
  view full answer...
• Recommended Amber, Red, And Clear Lens LED Clearance Lights For Karavan Boat Trailer
  The clearance lights we offer are not exactly the size you mentioned but these may work well for your trailer. I recommend part # AL82AB for the amber lights. These are LED lights and are submersible. These measure 2-1/2 inches long and 1-3/16 inches wide and 7/8 inch deep. For a red clearance light I recommend part # AL91RB. The clearance lights with a clear lens has amber colored diodes. We do not have a clear I recommend part # AL91CAB. All three of these lights have the same measurement...
  view full answer...
• Replacement Boat Trailer Lights for 2-3/4" Rough Cutout and 2-1/4" Grommet
  I have a solution for you, but we do not have any replacement lights that will fit in those grommets. Instead, you can use the LED Clearance or Side Marker Light # MCL002AXB (amber) and # MCL002RXB, which require a rough cutout dimension of 2-3/4", so they'll fit in your existing holes and provide you with the light solution you're looking for. These are waterproof LED lights so they're the perfect solution for a boat trailer as long as the rest of your lights are already LED. If your...
  view full answer...
• Procedure to Re-Install Trailer Side Marker Lights
  Installation methods will vary depending on the nature of the particular light you are using. We offer a wide range of clearance/marker lights (all can be seen on the link provided) and these include flange-, flush- and surface-mount types. You can use the filters in the left-hand margin to narrow the product results shown to just those light that meet your requirements. You can sort by lens color, bulb type, mounting type, brand and dimensions. For example, in 2-1/2- x 1-1/2-inch size...
  view full answer...
• What Size Hole Needs to be Drilled to Install 2-1/2 inch Optronics Clearance Light MC57RB
  The Sealed, 2-1/2" Round Trailer Clearance, Side Marker Light with Reflector # MC57RB requires the use of a the Grommet part # A55GB to install. This grommet will require a 3 inch hole to be drilled. For a pigtail harness you would need the part # A46PB as well.
  view full answer...
• Recommended Grommets Brackets And Plugs For 2 Inch LED Utility Light
  For the Optronics Clear LED Round Utility Light, part # UCL55CB, the grommet and brackets are different than those you listed. I will list the correct items you need for this light. The grommet needed for this light is part # A54GB. The mounting bracket designed for this light is part # BK5557GB. The two-pin plug you need for this light is part # A46PB. Part # A57GB and part # BK55BB are designed for a 2-1/2 inch light and will not work with the 2 inch light you referenced.
  view full answer...
• Replacement LED Light Recommendations For Trailer
  For a grommet mount red 2 inch clearance light I recommend part # MCL55R1224B. This light uses a 2-wire pigtail, part # A46PB for installation. If you need amber, you would order part # MCL55A1224B. Installed without a grommet, these lights measure 2 inches diameter x 1 inch deep. You can use the 2 inch grommet part # A54GB for this light for a flush mount. It would require a 2-5/16 inch mounting hole. The tail lights I recommend are the Optronics GLOLight LED Stop/Turn/Tail Light, part...
  view full answer...
• Replacement Side Marker Light and Grommet for a Trucklite Brand Grommet and Marker Light
  I went out to the warehouse and pulled grommet # A54GB and light # MC53AB. I then assemble them and the result looks exactly like your picture. I then measured the amount the lens sticks up above the grommet and came up with just under half an inch. The lens could be pressed further in. I used digital calipers to take the measurement. I also made a video showing the assembled result for you. The light takes wiring harness # A46PB if you do not already have them on your trailer.
  view full answer...
  
• Replacement Red, Round Side Marker Light for a 2010 Triton Trailer
  The SAE AP2 98 on the lens indicates the lens rating but it isn't a part number. Light # MCL59RB is 2-1/2 inches in diameter and takes grommet # A55GB and harness # A46PB. But none of the clearance lights we have that are round and 2-1/2 inches have the same lens rating.
  view full answer...
• Flush Mount Grommet and Wiring Pigtail for 2 Inch Clearance and Side Marker Lights
  The Sealed, 2" Round Trailer Clearance and Side Marker Light, Flush Mount - Amber # MC53AB or the LED # MCL55AB will use the 2" Round Grommet - Flush Mount - Open Back # A54GB for installation. You will also require the wiring pigtail # A46PB which will give you 6 inches lead.
  view full answer...
• Trailer Wiring and Lighting Replacement for Trailer with 4.5 inch Red and 2.5 inch Amber Light
  For a 4-1/2 inch diameter trailer taillight that can do stop/tail/turn functions we have the part # STL43RB which would work well. For a rubber grommet then we'd need the part # A45GB. Then for a pigtail harness you'd need the part # A47PB. For the 2-1/2 inch amber lights you'd want the part # MCL59AB and for a grommet for this you'd need part # A55GB. For a pigtail for this you'd want part # A46PB. Then for 4-way wiring sold by the foot you'd want the part # 16-4B-1.
  view full answer...
  

Do you have a question about this Accessories and Part?