Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for…
I&…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Subaru Ascent AccessoriesSelect A Category Below
Towing
Subaru Ascent Trailer Hitch
Subaru Ascent Trailer Wiring
Subaru Ascent Brake Controller
Subaru Ascent Towing Mirrors
Cargo Control
Subaru Ascent Roof Rack
Subaru Ascent Trunk Bike Rack
Performance Accessories
Subaru Ascent Air Filter
Subaru Ascent Suspension Enhancement
Subaru Ascent Vehicle Lights
Subaru Ascent Tire Chains
Subaru Ascent Fluid Filters
Subaru Ascent Salt Spreader
Subaru Ascent Cabin Air Filter
Vehicle Trim
Subaru Ascent Floor Mats
Subaru Ascent Trim Kits
Subaru Ascent Vehicle Covers
Subaru Ascent Mud Flaps
Subaru Ascent Vehicle Seat Covers
Subaru Ascent Windshield Wiper Blades
Subaru Ascent Windshield Covers