Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I&…
If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846.…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Mazda CX-9 AccessoriesSelect A Category Below
Towing
Mazda CX-9 Trailer Hitch
Mazda CX-9 Trailer Wiring
Mazda CX-9 Brake Controller
Mazda CX-9 Towing Mirrors
Mazda CX-9 Base Plate for Tow Bar
Cargo Control
Mazda CX-9 Roof Rack
Mazda CX-9 Trunk Bike Rack
Performance Accessories
Mazda CX-9 Air Filter
Mazda CX-9 Performance Chip Tuners
Mazda CX-9 Vehicle Lights
Mazda CX-9 Tire Chains
Mazda CX-9 Fluid Filters
Mazda CX-9 Salt Spreader
Mazda CX-9 Vehicle Engine Heaters
Mazda CX-9 Radiator Fan
Mazda CX-9 Cabin Air Filter
Vehicle Trim
Mazda CX-9 Floor Mats
Mazda CX-9 Vehicle Covers
Mazda CX-9 Side Window Vents
Mazda CX-9 Mud Flaps
Mazda CX-9 Vehicle Seat Covers
Mazda CX-9 Replacement Mirrors
Mazda CX-9 Windshield Wiper Blades
Mazda CX-9 Windshield Covers
Mazda CX-9 Vehicle Air Mattress