Customers compare DW04362 to these similar products
Products Featured in this Video
Today, we're taking a look at a Deka overmolded battery cable harness assembly. Now, this is a really simple design. What this does is it simply connects two batteries together.The overmolding is designed to protect the wiring. It's constructed of two AWG gauge PVC starter cable, and it does come with the protective caps that will go over and actually seal the battery connections.This unit's red… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Absolutely happy to do so, and let's start with the suspension support, and the best option for your 2019 Toyota Sienna is definitely the Air Lift 1000 Air Helper Springs for Coil Springs #AL60732. These install inside your Sienna's…
view full answer...Upgrading the rear suspension in your 2017 Toyota Sienna sounds like a solid plan considering all the weight you are carrying around inside your van. Since you're using a Sienna as a platform you are going to be limited on options for upgrades.…
view full answer...The TorkLift PowerArmor Solar Locking Battery Box part #TLA7700LS is not wide enough to fit two group 31 batteries. Group 31 batteries are 13" long by 6.72" wide by 9.44" tall. The only option that's big enough is the Commercial…
view full answer...According to the installation instructions for the #LC7333939, before the installation, the door trim on that side of the door will need to be removed up to a height of 29-1/2 inches. The lift assist bracket is meant to butt up against the outside of…
view full answer...The SolidStep Manual Fold-Down Steps #LC791575 do not require a lip on the threshold. They will work well with or without a lip as the mounting is flush and the hinge is a minimal rise. I've attached a video to assist so you can see the minimal…
view full answer...The Ultra-Fab Steel Jumbo Roller, #UF48-979023, was designed to help prevent taildragging on motorhomes and trailers so this would work great to help prevent damage to the undercarriage of your camper when going up steep driveways.
view full answer...The etrailer Trailer Hitch Receiver part #e75ZR which is a fit for a 2021 Toyota Highlander does have a hidden design which means the crosstube will not be visible, just the receiver tube. I have attached a photo below of the same hitch with a…
view full answer...The flashing by part #CPL65A-STR is done inside the light. These lights will flash, or strobe, 4 times per second as long as 12 volt power is supplied to the circuit they are attached to. You will need a switch to activate and shut down the flashing…
view full answer...In order to actuate the trailer brakes, you'd need a brake controller installed in the vehicle and a 6 or 7-way trailer connector. A 4 pole flat wiring harness like the #18002 you'd looked at carries 4 circuits- right turn/brake lamp, left…
view full answer...The auxiliary 12-volt wire that runs from the 7-way connection to 7-way trailer plug will supply 12-volt power from the vehicle to the trailer. The 12 -volt power will allow interior or exterior lights to run that are not wired in to the…
view full answer...The Roadmaster Battery Charge Line Kit #RM-156-75 and products similar to it are designed to keep the battery of the toad vehicle topped off while being flat towed. Typically supplemental braking system draw power from the battery of the tow vehicle…
view full answer...In order to charge a towed vehicle while in tow you will need a charge line kit for both the vehicle and motorhome. For this, we have the Roadmaster Battery Charge Line Kit for Motorhomes part #RM-156-75 and Roadmaster Battery Charge Line Kit for…
view full answer...