Troubleshooting Trailer Brakes that Stopped Working
Question:
Just installed new brake kit on both sides of the brake axel. Adjusted the brake controller and had good brakes for about 300 miles and then suddenly no brakes at all, I still have running lights and brake lights and turn signals, but no brakes.
asked by: John B
Expert Reply:
There are a number of reasons why the brakes on your trailer may not be working. Lets start with the easiest things to check.
First, check the vehicle and trailer connectors for corrosion. This can cause a short inside the connector and the brake feed circuit and ground are at the bottom of the connector so moisture affects these connections first.
Next, check the ground wire on the vehicle and trailer connectors, trailer brake magnets and the brake controller itself. If there is a bad ground connection the trailer brakes will not work.
Next, check the brake controller wiring. Sever the blue brake output wire, leaving enough room to splice it back together when testing is done and then apply the manual slide. Using a circuit tester, like item # PTW2993, you should get output to the trailer brakes. If the manual slide activates the trailer brake output wire properly, try the brake pedal. If the brake pedal activates the brake output properly the problem is farther back either in the vehicle wiring or on the trailer.
If either the brake pedal or the manual slide are not functioning properly you will need to test the wires going into the brake controller. Make sure you have power entering the brake controller on the black wire and on the red wire only when the brake pedal is pressed. If these wires test correct, and there is no output, your brake controller most likely needs to be replaced.
I attached an FAQ on troubleshooting brake controllers for you to check out as well.
Products Referenced in This Question
Product Page this Question was Asked From
Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Dexter Electric Trailer Brake Kit Installation
- Q&A: How to Know When Trailer Brake Magnets are Worn Out and Need Replacing
- Shop: Grease Seal - Double Lip - Inner Diameter 1.68" - Outer Diameter: 2.33" - Qty 1
- Shop: Dexter Electric Trailer Brake Assembly - 7" - Right Hand - 2,000-lbs to 2,200-lbs
- Shop: Dexter Electric Trailer Brake Assembly - 7" - Left Hand - - 2,000-lbs to 2,200-lbs
- Shop: Deka Heat Shrink Butt Connector - 16-14 Gauge - Nylon Insulation - Blue - Qty 10
- Shop: Bearing Kit, L44649 Inner/Outer Bearings, 10-9 Seal
- Shop: Dexter Electric Trailer Brakes - 7" - Left/Right Hand Assemblies - 2,000 lbs to 2,200 lbs
- Shop: Grease Seals (pair)
- Search Results: grease seal 10 60
- Search Results: 10 60 seal
- Search Results: heat shrink butt connector
- Video: Trailer Brakes and Wiring Installation
- Q&A: Determining Brake Controller Mounting Location on 2018 Dodge Durango
- Q&A: Troubleshooting Prodigy P3 Brake Controller 90195 That Only Works with Manual Override
- Search Results: pro series weight distributing hitch
- Q&A: Troubleshooting No Power To Trailer Brakes When Trailer Connected To New GM Truck
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: brake controller
- Shop: Brake Controller
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer brake controller
- Video: Choosing the Right Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: trailer brakes
on Accessories and Parts
