Does Bolt for Timbren Front Suspension Enhancement System # TFF350SDC Match the OEM Bolt

Question

Question:

before I start to install the front Timbren, the OEM mount used one bolt only into the frame, no nut on the other end. My question is if Timbren has the same size of thread on supplied bolt that will match the OEM bolt ? I dont want to pry out the bump stop then find out the thread is different.....

asked by: Paul T

0

Expert Reply:

I spoke with my contact at Timbren and he said the bolt supplied with your Timbren Front Suspension Enhancement System # TFF350SDC that goes from axle to frame should match the OEM bolt. If not, you can use the factory bolt.

I have included a link to the installation instructions at right.

expert reply by: Chris O

0

Answer 1

On your 2014 Ford F-350 you can remove the existing factory jounce bumper assembly by grasping it firmly and with a twisting and pulling motion, work it until the jounce bumper pops out of the retaining cup. It can also be pried out of the…

view full answer...

Answer 2

We have two Timbren rear suspension kits that fit your 2020 Ford F-250 we have the standard duty #TFRTT350J which has a spring height of 3-9/16 inch and a bracket height of 2-3/8 inches. The severe duty #TFR250SDJ is 3-5/8 inches tall and has the…

view full answer...

Answer 3

Generally speaking, most leveling kits lift the front of the truck 1-2" to match the rear as the factory ride height on most pickup trucks nowadays is about 2" lower in the front than in the rear. This is usually to compensate for…

view full answer...

Answer 4

The Timbren Rear Suspension Enhancement System #TGMRCK25S is a correct fit for your 2005 Chevrolet Silverado 2500 whether it is a 2WD or a 4WD version. This kit will install without need for the included 7/8-inch thick spacers UNLESS the truck has a…

view full answer...

Answer 5

There are front axle Timbrens available for the 2019 Ford F-350 4X4 with part #TFF350SDC. The Timbren Front Suspension Enhancement system will require spacers if you have a suspension lift. If it's a body lift you won't need the spacers. If…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Does Bolt for Timbren Front Suspension Enhancement System # TFF350SDC Match the OEM Bolt

Product Page this Question was Asked From

Continue Researching