Shape of Mounting Holes for Trailer D-Ring Tie Down RR05

Question

Question:

DO THESE D RING RECESSED TIE DOWN HAVE SQUARE OR ROUND MOUNTING HOLES? THE ORIGINAL PICTURE SHOWS SQUARE BUT THE FOLLOWING SHOW ROUND

asked by: ANTHONY C

0

Expert Reply:

The mounting holes for Trailer D-Ring Tie Down, Recessed 5K, # RR05, are square. The picture used that shows round holes is a stock photo to show measurements.

expert reply by: Michael H

0

Answer 1

The strap on the Erickson Adjustable Ratcheting Wheel Net part #EM58522 that is ran through the loop and then contains the hook is 13-1/2" long.

view full answer...

Answer 2

For use with D-ring tie downs you could use wheel net #EM58522 with your Polaris Ranger. It has a safe working load limit of 3,333 pounds and break strength of 10,000 pounds. The Pack'Em Wheel Tie-Down Kit for Truck Beds and Trailers #PK-WTD…

view full answer...

Answer 3

I can absolutely help you and make a recommendation. The floor of your Big Tex 70 car trailer is an 1/8 diamond steel plate. The 1/8 plate will be fine for a tie down point for anything but a car. You need a bracket not to fasten something down tight…

view full answer...

Answer 4

The Brophy Swiveling D-Ring Anchors with Backing Plates and Hardware part #RR6K-4 no longer comes with hex bolts. Instead, it comes with carriage bolts now which makes for a smoother surface once finished.

view full answer...

Answer 5

The Brophy D-Ring Tie Down Anchor #RR05 can be bolted or welded. The #RR05 has a zinc plating so it takes a specific type welding and ventilation when welding. I recommend checking with a certified welding professional to discuss how these should be…

view full answer...

Answer 6

Since the hole will be covered by the D-ring #RR05 you'll still have a professional look if you us a chisel. When we installed them (see the linked video) we actually drilled all the way through the trailer floor because it was plywood. We used a…

view full answer...

Answer 7

Hey Dwayne that is a great question. Generally, we would want the tie down points to be in line with the front and rear of the tire. So the #EM58522 straps would hang straight down and connect to the #RR05 D-ring. You can also angle them forward if…

view full answer...

Answer 8

The Erickson Replacement Adjustable Wheel Net for 14" to 29" Tires #EM58518 are designed so that you can set the adjustment mechanism/clamp to either side of the tire, so that they're always on the outside and easily accessible. These…

view full answer...

Answer 9

The best option we have for you to add additional tie-downs to your car hauler would be to use Brophy D-Ring Tie Down Anchors part #RR5K. You could weld the top plate to the diamond plate flooring or you could drill a few holes and use the included…

view full answer...

Answer 10

The Pack'Em Wheel Tie-Down Kit for Transporting Machines w/ Wheels, part #PK-WTD is designed to secure one tire in place on a truck bed or deck.

view full answer...

Answer 11

We have the Ultra-Fab Solar-Powered Plumbing Vent for Motor Homes - 7" Diameter x 3-3/4" Tall #UF53-945001 which is designed to be mounted on the roof. My recommendation is to use this roof vent and allow your side vents to stay as they…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Shape of Mounting Holes for Trailer D-Ring Tie Down RR05

Product Page this Question was Asked From

Continue Researching