What Diameter Studs are Used in the Trailer Hub Assembly # 845475UC1

Question

Question:

What size studs are used on these hubs?

asked by: Chris T

0

Expert Reply:

The studs that are used in the Hub part # 845475UC1 are 1/2 inch in diameter. I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I was unable to find any reference to a Dico 45264 hub. You will need to take some of the measurements to make sure you get the correct bearings and seals for your trailer. Trailer manufacturers use many different sizes when they build their systems…

view full answer...

Answer 2

If you want to switch out the hubs what you need to do is find the bearing and seal part numbers from the original hubs. Any new hub must use the same bearings and seals as the original in order for it to fit properly on your spindles. Examples of…

view full answer...

Answer 3

From what I have found your Dexter 8-248 hub is for a 3,500 lb axle. It uses #L68149 inner and #L44649 outer bearings. The hub has two possible bolt patterns so you will need to choose the correct replacement based on the bolt pattern on your current…

view full answer...

Answer 4

The Dexter "8-248" is a hub assembly for 3,500 lb axles that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in both 5 on 4-1/2" and 5 on 4-3/4" bolt patterns therefore you would need to…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 10

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

What Diameter Studs are Used in the Trailer Hub Assembly # 845475UC1

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching