Replacement Tonneau Cover Tarp for 2002 Dodge Ram 1500 6ft bed w Extang Platinum Classic Tonneau

Question

Question:

Just want to make sure this is the correct replacement for my 2002 Dodge Ram 1500 6ft bed. for Extang Platinum Classic Tonneau cover. The old one simply ripped.

asked by: Fran

0

Expert Reply:

As long as the Extang Platinum Classic Tonneau Cover that you have on your 2002 Dodge Ram is part number 7770 (it should be) then the part # EX6770 that you referenced would be the correct replacement tarp.

The part number 7770 is the correct Extang Platinum Classic Tonneau Cover for your vehicle so it should work, but I would still recommend you verify this.

expert reply by: Jameson C

0

Answer 1

I reached out to my contact at Extang and the correct cover is the Replacement Tarp for Extang Classic Platinum Tonneau Cover-Black #EX6770 for your 2007 Ram 1500 Short Bed.

view full answer...

Answer 2

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 3

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 9

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Replacement Tonneau Cover Tarp for 2002 Dodge Ram 1500 6ft bed w Extang Platinum Classic Tonneau

Product Page this Question was Asked From

Continue Researching