Replacement Mounting Hardware for a Trailer Hitch on a 2001 Toyota 4Runner

Question

Question:

I am looking for a replacement hardware kit to re-install a Curt 13087 hitch on a 2001 Toyota 4runner. I needed to cut the bolts and the nut plate weldments are rusted away. I would need the nut wire also for the center holes

asked by: Todd K

0

Expert Reply:

You can use # RHK and enter the hitch number and manufacturer where indicated on the page. This will get you the bolts and washers but those long specialty nuts, one for each side, have to be obtained from Curt directly. For a 1/2 inch bolt leader use # C58400.

expert reply by: Michael H

0

Answer 1

To get the exact replacement hardware for your traier hitch you need to know it's model number and the manufacturer. With this information use part #RHK and enter the part number and select the manufacturer from the drop down menu. I've…

view full answer...

Answer 2

Yes, we do sell the installation hardware for the Curt trailer hitch receiver #C13087. Use part #RHK and then select "Curt" from the drop down and enter the part number. This will order the exact hardware that is included with a new hitch.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 7

You will need to order the Replacement Hardware Kit #RHK. On the product page you will enter Curt Trailer Hitch Receiver #13147. This will then supply you with all the hardware to install the receiver on a 2009-2013 Subaru Forester. If you are also…

view full answer...

Answer 8

I do have a solution for you, however the closest spacer block we currently have available to the dimensions you listed in your question is the Reese Spacer Block #RP3022. The size of this spacer block is 1/4" x 1" x 3". If you are…

view full answer...

Answer 9

No, the Replacement Mounting Hardware #C75JR is not going to fit the Curt Class III Hitch #C13135. If you are in need of a hardware kit for the #C13135 hitch, we can provide that with Part #RHK. When you go to the page for #RHK you will see a box…

view full answer...

Answer 10

The Draw-Tite Max-Frame Trailer Hitch Receiver #76020 for your 2023 Mazda CX-9 is no longer compatible with the J-Pin 63201. Draw-Tite stopped making their receivers compatible with this pin in 2021 and we have long sold through all those receivers.…

view full answer...

Answer 11

Yes, the Curt EXO Swing Away Enclosed Cargo Carrier part #Y62VR is perfectly compatible with the 2 inch Curt Hitch part #C13305 you have installed on your 2018 Volvo S90. The shank of this has enough rise built into it that you would not have any…

view full answer...

Replacement Mounting Hardware for a Trailer Hitch on a 2001 Toyota 4Runner

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching