How Tall is the motor On Ultra-Fab 12K Landing Gear

Question

Question:

what is the distance from the top of the motor to the minimum of the top of the top brackett? Im trying to decide which jack set to get. Dont really like the Atwood with dual motors

asked by: Russel S

1

Helpful Expert Reply:

The motor on the Ultra-Fab landing gear # UF17-943010 is approximately 9 inches tall from the top to the bottom where it is attached. The top bracket is directly below the bottom of the motor about another 1/2 inch to 3/4 inches below.

expert reply by: Michael H

1

Answer 1

I am not sure which dimensions you need. We have a picture that shows the dimensions on the product page. It is the very last thumbnail right next to the main picture. And the instructions are linked on the page, right hand side with even more…

view full answer...

Answer 2

The distance from the top of the top welded tab to the bottom of the bottom welded tab on the Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 is 21-1/8 inches.

view full answer...

Answer 3

Typically around the motor area of the stabilizer jack there will be a label that will have part numbers and other info listed. I attached a picture of what it looks like on the #LC298707 that you referenced. Lippert does sometimes use alternate…

view full answer...

Answer 4

The motors on the Ultra-Fab landing gear #UF17-943010 are 8.922 inches tall. Positioning the jacks so that there is enough room for them is a viable option provided that you can do so safely and so that the jack legs do not decrease ground…

view full answer...

Answer 5

The Ultra-Fab Deluxe Electric Landing Gear Set #UF17-943010 referenced in your question is a great landing gear system that features dual electric jacks that will raise and lower at just the flip of a switch. The jacks themselves can operate…

view full answer...

Answer 6

The Ultra-Fab Deluxe Electric Landing Gear Set - 38" Lift - 12,000 lbs #UF17-943010 is a great set to replace your factory landing gear on your 2007 Heartland Sundance 3012RE. I've attached some measurements to assist in ensuring a fit with…

view full answer...

Answer 7

We do carry electric dual motor landing gears for fifth wheel trailers. The biggest landing gear set we carry is the Ultra-Fab Deluxe Electric Landing Gear Set, part #UF17-943010. This has a 12,000 lb weight capacity and features two 12 volt motors…

view full answer...

Answer 8

Yes, in case of a power failure, the levelers of the Ultra-Fab Landing Gear Set #UF17-943010 can be operated manually by removing the four screws that hold the motor/gear assembly. The slotted shaft can then be turned with a large flathead…

view full answer...

Answer 9

According to my contact at Ultra-Fab, their Deluxe Electric Landing Gear Set #UF17-943010 has an overall height, including the motor assembly, of 36.55-inches with the leg fully retracted. Please refer to the linked diagram for the rest of the…

view full answer...

Answer 10

In order for a 'right out of the box' fit for the Ultra-Fab #UF17-943010 fifth wheel landing gear, the underside of your top mounting bracket and the underside of your bottom mounting bracket would need to be 19-1/8 inches apart, as shown in…

view full answer...

Answer 11

Judging by the condition of your landing gear a new motor isn't all that you'll need. Plus the motor kit you mentioned is for stabilizer jacks which are a totally different style of jack. Your best solution will be a new Ultra Fab power…

view full answer...

Answer 12

For your 2004 Alpenlite 5th Wheel the Lippert landing gear set part number LC333964 would be a really great option. This would fit the standard landing gear bracket dimensions you have and would work quicker than other options as it has a higher 6k…

view full answer...

How Tall is the motor On Ultra-Fab 12K Landing Gear

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching