Installation Instructions for part # RM-4139-125

Question

Question:

Hello, I discovered the bushings on my 1999 Fourwinds Infinity V10 F53 motorhome where gone. I could move the bar around in the bushing holder. I was trying to view the installation instructions on your website but it would not work. Could you provide those to me. Thanks.

asked by: Kevin S

0

Expert Reply:

I apologize for the issue with the instructions link. I attached pictures that I took from the installation instructions that will show you how it installs.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Since the bolts that come with the Roadmaster Polyurethane Bushing Kit #RM-4139-125 are designed to attach to threaded parts of the vehicle suspension nuts are not included or needed. Check out the install video I attached for more info on how it…

view full answer...

Answer 2

In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs…

view full answer...

Answer 3

I am not sure what is wrong with the links but I have included a picture of the instructions for the rear, #RM-4139-125, and for the front, #RM-4139-127, for your RV built on the 1997 Ford F-53. V8 chassis. The rear is on the top and the front is on…

view full answer...

Answer 4

From the images you attached, description provided, etc. the Press In Window Edge Weatherstrip for Enclosed Trailer, #SR43FR that we offer is a similar product to what you have only in black. This will work as a replacement item if black is…

view full answer...

Answer 5

I did some checking on your 1999 Fleetwood Bounder 34v and it appears that it was built on the Ford F53 chassis which is a common one for Class A RVs. There is a bushing upgrade kit for the rear anti-sway bar and it is #RM-4139-125. The single…

view full answer...

Answer 6

It sounds like you're looking for the Roadmaster Polyurethane Bushing Kit for 1-1/2" Diameter, Factory Rear Anti-Sway Bar #RM-4139-125, which would fit on your 1-1/2" diameter Roadmaster rear anti-sway bar. These are definitely better…

view full answer...

Answer 7

Some of the bushings on the Roadmaster #RM-4139-125 will need to be pressed in, but it is not overly difficult. I included an install video we have of a similar Roadmaster kit that will show how this needs to be done.

view full answer...

Answer 8

the Replacement Toilet Bowl Seal Kit for Dometic Sealand and VacuFlush RV Toilets #DOM35FR is designed to work with Dometic, SeaLand & VacuFlush RV toilets from 2000 or earlier, and will not work with your Dometic 503 toilet. Instead, take a look…

view full answer...

Answer 9

Most modern tow dollies are either wide enough to handle most any late model vehicle that can be placed on a dolly or width adjustable to accommodate a variety of vehicle styles. The RoadMaster Tow Dolly with Electric Brakes, #RM-2050-1, is one of…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Installation Instructions for part # RM-4139-125

Product Page this Question was Asked From

Continue Researching