Which Hole of the CE Smith Tie-Down Bracket # CE26214G Mounts to the Trailer

Question

Question:

Which of the two hole is the mounting hole that fastens the bracket to the trailer? Also: In one part of the description I saw it said there was a 30 degree mounting angle and in another it said 45 degree mounting angle. Which one is correct?

asked by: Dave

1

Helpful Expert Reply:

The smaller hole of the CE Smith Tie-Down Bracket # CE26214G is the mounting hole that secures the bracket to the trailer. The smaller hole is 9/16 of an inch and the larger hole is 7/8 of an inch.

The bracket has a 30 degree angle to it. I apologize for the confusion.

expert reply by: Jameson C

1

Answer 1

A Grade 5 bolt or higher would be recommended for use with the CE Smith Tie-Down Bracket #CE26214G.

view full answer...

Answer 2

Your ride quality issue is caused by not having enough tongue weight like you mentioned. You need the trailer tongue weight to be between 10 and 15 percent of the total trailer weight. Your tongue weight being 450 lbs while the trailer weighs 6,300…

view full answer...

Answer 3

You should have the hitch ball height set so that the trailer tows as level as possible behind your pickup. If there is a setting that goes between slightly higher than level and slightly lower than level, opt for the slightly lower setting, when the…

view full answer...

Answer 4

I went and pulled a CE Smith Tie-Down Bracket #CE26214G from our warehouse to measure the dimensions and found that the overall length is 4 inches, the width is 1-15/16 inches, the bigger hole is 7/8 of an inch and the smaller hole is 9/16 of an…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...