Replacement Tail Lights for a 1977 Shasta 1600 Trailer

Question

Question:

I need tail lights for my 1977 Shasta 1600 would these lights fit my trailer ? would I need anything else ?

asked by: Lawrence

0

Expert Reply:

Based on your picture it looks like the left side is # 30-92-004 and the right side would be # 30-92-002. These lights are 8-9/16 inches across, 4-9/16 inches tall, and 2-1/8 inches deep.

Just for reference on the wiring, since you can't always go by wire color:

Red wire: Reverse light circuit
Green wire: Tail light circuit
Black wire: Blinker and brake circuit
White wire: Ground wire to trailer frame

expert reply by: Michael H

0

click to enlarge

Answer 1

I assume this is a replacement axle, so in order to choose the correct one, you will need to know the dimensions of your current axle's hub-face to hub-face and spring center to spring center as in the diagram I have added, with A being the hub…

view full answer...

Answer 2

The spindle dimensions are as follows: A is the mounting dimension, B is the seal dimension, C is the inner bearing surface, D is the outer bearing surface and E is the diameter of the threaded portion of the spindle for spindle nut selection. Say…

view full answer...

Answer 3

To replace a spindle, the old one would need to be cut off, and the new one welded into place. This is NOT a job for the do-it-yourselfer. The new spindle must be absolutely square with the axle in order to prevent premature tire wear and wheel…

view full answer...

Answer 4

If you're looking for the driver's side version of the #30-92-002, you'll want the #30-92-004, which has the built in license plate bracket and license plate light. Once you remove the lens, and the screws holding the lamp housing to the…

view full answer...

Answer 5

It sounds like you're needing a Bargman 92/94 series taillight. The DOT number you provided usually doesn't steer us to a replacement lamp, the actual part number of your lamps should be printed or stamped on the lamp housings themselves, not…

view full answer...

Answer 6

The correct replacement panel for you is the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 35 Amp #PD4135K. As you can see this is an 35 amp panel just like your WFCO-8735-P which means it is a safe…

view full answer...

Answer 7

I took a look at the online owner's manual for your 2017 Honda Fit EX. It starts off by stating that only the manual transmission models of the Honda Fit can be towed behind a motorhome with all four wheels on the ground. For extended towing…

view full answer...

Answer 8

I do have a suggestion, because we have a gas strut with with dimensions that are the same as the Stabilus 654150 which is likely to work; the Stabilus strut measures 26.46" when extended with 120 lbs of force. The nearly identical strut we…

view full answer...

Answer 9

Fasteners are not included with the Triple LED Trailer Tail Light #CE44VR. This is due to the different mounting surfaces that the lights can be mounted to. Depending on the surface that the lights will be mounted to will require different hardware…

view full answer...

Answer 10

For your Lance 855s Camper with standard tracks I recommend the Rhino-Rack Quick Mount Legs for Vortex Aero Crossbars - RTC and RT Roof Rack Tracks - Qty 4 #RRRLT600 and then crossbars like the Rhino-Rack Vortex Aero Crossbars - Aluminum - Black -…

view full answer...

Answer 11

The Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch - Remote - 2,000 Watts - 12V Item #PD64FR will pull DC current from your battery and convert it to AC current for when you aren't hooked up to shore or generator power. The…

view full answer...

Replacement Tail Lights for a 1977 Shasta 1600 Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching