Roll-Up Tonneau Cover for a 2008 Ford F-150 with a Toolbox

Question

Question:

2008 F150 8 body. Oversized toolbox. I have between 62 and 66 inches between box and tailgate. Is cover 834532004829 going to fit OK?

asked by: Morton

0

Expert Reply:

As long as your tool box is between 20 inches and 21 inches, the cover will work for you. If your tool box is any wider than that, it will not work.

expert reply by: Amanda

0

Answer 1

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 2

Although the #834532004829 isn't a fit for your truck, we do have a specific fit for your truck. The Access #834532001859 Toolbox Edition is a confirmed fit for your truck, and it's compatible with over-the-rail or crossover type…

view full answer...

Answer 3

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System #LC736514-ELKIT then you'll need part #LC182492. The flat bracket can be swapped out with part #LC182494 and the swing brackets can be replaced with…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Congrats on the new truck! You won't have to swap our your Curt Q20 Hitch but you will need to use an adapter because GM changed the puck pattern in 2020. The correct adapter is the Item #C88KR you were looking at. This will mount directly to the…

view full answer...

Answer 8

I would be happy to! To add a gooseneck hitch to your 2024 GMC Sierra 2500, I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit item #BWGNRK1020. This hitch is custom fit and includes all hardware…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Looking at pictures I found of the 2002 Lance 1121 it looks like it has HappiJac jacks on it. For the brackets you can use the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems #LC182496. The replacement legs will require more…

view full answer...

Answer 11

The highest capacity gooseneck hitch for a 2024 Chevrolet Silverado 3500 is the Curt Custom Underbed OEM-Style Gooseneck Trailer Hitch item #C60642. It has a 32,500 lbs towing capacity. The Curt gooseneck system item #C60642 fits both the 6-3/4'…

view full answer...

Answer 12

For your setup I recommend the TrackTowers for Yakima Crossbars and Platforms - Track Mount #Y52AV which includes everything you need to mount Yakima crossbars to your Retrax cover (unless you plan on using the Round or HD bars - then you'll need…

view full answer...

Roll-Up Tonneau Cover for a 2008 Ford F-150 with a Toolbox

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching