Replacement Mounting Brackets For HappiJac Electric Truck Camper Jack System

Question

Question:

I have the jacks in LC736514-ELKIT and the bracket that attaches the jack to the camper is bent, causing the jack to lean outwards. I would like to replace the bracket the jack is fine - do you sell the brackets separately?

asked by: David N

0

Expert Reply:

If you're looking for just the L-bracket for your HappiJac Electric Truck Camper Jack System # LC736514-ELKIT then you'll need part # LC182492. The flat bracket can be swapped out with part # LC182494 and the swing brackets can be replaced with part # LC182496.

expert reply by: Kevin C

0

HappiJac Electric Truck Camper Jack System Mounting Brackets
(click to enlarge)

Answer 1

Yes the Happijac swing out bracket kit part #LC182496 does work with your camper with a set of Happjac truck camper jacks and would also work/be needed for your 2021 Ram truck that is a dually.

view full answer...

Answer 2

From the pivot bolt to the jack bracket on the Swing Out #LC182496 there is a distance of just about 4-1/2".

view full answer...

Answer 3

The Furrion #FR87PR 7-way vehicle power adapter cable would indeed be necessary for the camera system to function. The problem is that newer Ford and GM trucks equipped with 'Trailer Management' or 'Smart Trailer Connectors' don't…

view full answer...

Answer 4

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 5

The HappiJac Electric Truck Camper Jack System #LC736514-ELKIT is the replacement kit for the 4100 series jacks that you have. It uses the same Replacement Jack #LC736514 and Motor Head #LC759927 for the front and rear jack positions.

view full answer...

Answer 6

Looking at pictures I found of the 2002 Lance 1121 it looks like it has HappiJac jacks on it. For the brackets you can use the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems #LC182496. The replacement legs will require more…

view full answer...

Answer 7

Starting off with air bags I recommend getting the Firestone #F2400. Firestone air bags have the best construction and are the most reliable. These have 5,000 lbs of load-leveling capacity and come with a lifetime warranty on the air springs. If you…

view full answer...

Answer 8

I can absolutely confirm the correct lift kit for your trailer. Based on your photos, you do in fact have a #10 Torflex axle, and they are compatible with the lift kits because you do not have 3" high-profile brackets (which just means the…

view full answer...

Answer 9

Yes, the Replacement Jack for HappiJac Truck Camper Jack System part #LC736514 (Model 4220) will fit your HappiJac Truck Camper Jack System Model 4150. If you need a new gearbox/motor then we have that as well, the Replacement Motor and Gear Head…

view full answer...

Answer 10

The clicking you described hearing on your Happijack 4150 System along with the fact that they aren't raising or lowering the camper might actually be the result of a weak power source. I first recommend simply checking to make sure that the…

view full answer...

Answer 11

Thanks for the picture! I would be happy to help you Yes, you are correct in assuming you will only need one set of the Swing Out Extension Brackets for HappiJac Truck Camper Jack Systems Item #LC182496. These come in pairs and you will not need them…

view full answer...

Replacement Mounting Brackets For HappiJac Electric Truck Camper Jack System

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching