What are the Measurements of the UWS Twist Lock When it is Closed

Question

Question:

how long is the twist lock when it is close

asked by: Roger B

0

Expert Reply:

When closed the lock # UWSTWISTLOCK is 1-7/8 inches tall and 1-1/2 inches wide. I included a picture showing this and other relevant measurements for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

The UWS Truck Bed Toolbox - Crossover Style - Single Lid Series - 6.9 cu ft - Gloss Black #UWS00327 or bright aluminum #UWS00076 are the TBS-54 options. There are also two low profile options in the #UWS00371 or #UWS00381. All of these installations…

view full answer...

Answer 2

I went out to the warehouse to measure this lens and found the diameter of Replacement Lens #A41CB to be 4-1/4 inches.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Yakima's Skyline towers part #Y53TR can fit the tracks of the Retrax XR that you have with the landing pad 1 part #Y00221 but there isn't a way with the Baseline towers. Your Yakima Corebar or Jetstream bars will work with the Skyline towers…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

What are the Measurements of the UWS Twist Lock When it is Closed

Product Page this Question was Asked From

Continue Researching