Aluminum Fender Recommendation For Trailer

Question

Question:

I am looking for an aluminum fender with back that is similar to your HP36VR. Do you have for know where I might be able to get one? Thanks,

asked by: Ken W

0

Expert Reply:

We do offer an aluminum trailer fender but it does not feature the backing used for mounting like part # HP36VR.

The aluminum fender we carry is part # HP96VR. The installation of this fender is done by drilling and using mounting screws in the lip of the fender. I have attached a link to a video that shows how these fenders are installer.

expert reply by: Jeffrey L

0

Gary C.

5/15/2024

I am trying to find the attached link to video showing how to install the hp96vr fenders

Reply

Answer 1

We offer 2 different Jeep Style fenders that are designed to work with 15 inch wheels. The aluminum fender we carry is the etrailer brand Trailer fender, part #HP96VR. This fender has a 1/2 inch radius lip on both the front and the back of the fender…

view full answer...

Answer 2

The included hardware that comes with the Plastic, Single-Axle Trailer Fenders #PF11X35W-2 is the Galvanized Steel, U-Shaped, Bolt-On Brackets #PF1135-BKT-2. I attached a couple pictures of the brackets for you to check out also.

view full answer...

Answer 3

Our selection of trailer tires in the 205/75-14 size with a D load range is limited to Kenda Karrie and Westlake. These both are considered higher quality radial options but the best one for your application will come down to your particular speed vs…

view full answer...

Answer 4

For your Karavan trailer I recommend LED tail lights #STL57RB and #STL56RB. They are a little shorter at 6-1/16 inches but they do mount on studs spaced 2 inches apart on center. they are 3-5/8 inches tall and 2-1/4 inches deep overall. I have linked…

view full answer...

Answer 5

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The Prime Guard Wheel Bearing Hi-Temp Red Grease part #L11380 16-oz tub will be enough to pack the wheel bearings and grease the spindle on your travel trailer. I have attached a helpful article for your reference about packing the bearings. The…

view full answer...

Answer 10

The closest trailer fender we have available to the dimensions you mentioned is a Jeep Style Fender like the etrailer brand #HP96VR. This aluminum fender is 33 inches long, 10 inches wide and 17 inches tall. It is designed to fit with 13-15 inch…

view full answer...

Answer 11

We won't have an exact OEM fender part for your 1997 EZ-Loader boat trailer but we do offer a range of general purpose trailer fenders in plastic, aluminum and steel. I linked for you just the plastic fenders we have for 14-inch wheels and the…

view full answer...

Answer 12

Tires have a heavy spot and a light spot, so the markings on the tires applied in the manufacturing process, are intended to be a guide for tire technicians so they have an idea of where to mount the tire on the wheel. It's important to point out…

view full answer...