7-Way Mounting Bracket for Use with ETBC7L and Curt Echo Mobile Brake Controller

Question

Question:

Hello! I believe I need a bracket to mount ETBC7L to my square bar U-Haul hitch on my 07 Touareg. Do you have a recommendation before I purchase this and the curt Bluetooth brake controller?

asked by: Ray F

0

Expert Reply:

Hey Ray, so we have the part # 18159 which would work great to secure the 7-way of the # ETBC7L that you'll be installing with the Curt Echo # C51180. It's also pretty easy to install too.

expert reply by: Jameson C

0

Ray F.

5/22/2024

Thanks, Jameson! My hitch is hidden under the bumper so not sure this would work. Any other options?

Reply

Jameson C.

5/22/2024

@RayF I'd attach it to the lower edge of the rear bumper with a bolt on bracket like the part # 18138 instead.

Reply

Ray F.

5/22/2024

@JamesonC does the ETBC7L come with a similar bracket? So technically I would be able to just use the provided bracket on the bumper? Just making sure I’m not buying extra parts

Reply

Jameson C.

5/22/2024

@RayF Yes it does. I should have mentioned that earlier sorry for the confusion.

Reply

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

7-Way Mounting Bracket for Use with ETBC7L and Curt Echo Mobile Brake Controller

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching