Is There Maintenance Video for Bulldog A-Frame Jack # BD1700100317

Question

Question:

Do you have a maintenance video for this jack?

asked by: Charley

0

Expert Reply:

Hey Charley, so trailer jacks like the Bulldog part # BD1700100317 that you referenced don't have set maintenance procedures so we don't have a maintenance video we can share with you. There really isn't anything to do to maintain it aside from maybe just try not to drag it on driveway curbs.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 3

Hello again, James. We will need to consider a different approach here because the Timbren Silent Ride Suspension like part #TSR3500S05 cannot be used with torsion axles. In order to use the Silent Ride you would need to completely replace both…

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

David, the threaded portion on the Replacement Gauge for Valterra Adjustable Water Regulator #A01-1125 is 1/2&quot;.

view full answer...

Answer 6

To charge the battery while the boat is running you would need to install solar panels which depending on your boat might not be an option. Typically most people run multiple batteries in parallel to run their appliances/equipment. Since…

view full answer...

Answer 7

I went out to the warehouse and measured the Bulldog Round, A-Frame Jack , item #BD1700100317, and there is 7 inches of clearance from the top of the mounting flange to the bottom of the lowest point on the jack handle. It sounds like this is…

view full answer...

Answer 8

I have good news, our trailer jack that has a 2 inch outer diameter part #DL74MR would fit and work well. While it has a 1,000 lb weight capacity that does not mean 1,000 lb total trailer weight capacity. That capacity is the tongue weight capacity…

view full answer...

Answer 9

Your 4-pin/5-wire wiring harness is what is called a "wishbone" type which simply means that there are two separate running light wires, one brown and one pink. This allows a separate running light wire for each side of the trailer…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

As the FMSMA15-SS has been discontinued, I could not confirm the size of the exhaust filter that fits it, unfortunately. However, I can confirm that the Replacement Ventilation Exhaust Filter for Furrion Over the Range RV Convection Microwave…

view full answer...

Answer 12

Yes, 14 gauge wire seems too small. I would go with 10 or 12 gauge. For 10 gauge you can use #10-1-1 and for 12 gauge use #12-1-1. These wires are sold in increments of 1 foot. So if you needed 20 feet of wire you would enter 20 in the quantity…

view full answer...

Is There Maintenance Video for Bulldog A-Frame Jack # BD1700100317

Product Page this Question was Asked From

Continue Researching