Which Race is Correct for Trailer Hub Bearing LM67048

Question

Question:

You dont have the correct race for bearing LM67048,you show race L44610 when it should be LM67010 and bearing L68149 should be raceL68111. this is for hub 08-407-5.

asked by: Randy B

0

Expert Reply:

Hey Randy, I am not sure where you saw that the # LM67048 race is the # L44610 but it is for sure the # LM67010.

expert reply by: Jameson C

0

Answer 1

Your bearing number combination is pretty rare but it actually matches 4,400 lb axle hubs like the Dexter part #8-407-5UC3-EZ. This will give you a hub/drum that has a 6 on 5-1/2 inch bolt pattern.

view full answer...

Answer 2

The Trailer Hub and Drum Assembly part #8-407-5UC3-EZ is sold individually or as a quantity of one. It will require two per axle for a complete set.

view full answer...

Answer 3

It certainly does. What you have there is a hub for a 4,400 lb axle. To replace it you will need the #8-407-5UC3-EZ. This includes the hub/drum, new bearings, races, grease seal and lug nuts.

view full answer...

Answer 4

The Trailer Hub and Drum Assembly #8-407-5UC3-EZ is a lug centered hub with a pilot hole size of 3.62". Your 99.25mm(3.75") hub bore wheels will fit on hub/drum.

view full answer...

Answer 5

You need Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2, part #8-407-5UC3-EZ. This is the hub comes with the bearings, races, and seals. The drum that is compatible is the Dexter Electric Brake Assembly for…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Which Race is Correct for Trailer Hub Bearing LM67048

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching