Recommended Spring Seat for a 2,200 lbs Axle w/ a 1-3/4" Diameter

Question

Question:

Can I specify a custom spring seat distance AND have it pre-set up for an axle flip? Thanks.

asked by: Dan B

0

Expert Reply:

No, sorry Dan you can not. We have all the parts you need to move the spring seats on the Dexter Trailer Idler Axle w/ Hubs item # 20545I-EZ-72-10 you were looking at but we do not install them. You will need two of the Spring Seat for Typical 2,000-lb, Round Trailer Axles item # TRSS175 for a 1-3/4" diameter axle.

expert reply by: Jerred H

0

Answer 1

Thanks for the picture and your patience! I just heard back from Dexter and your D20 axle uses the same inner and outer bearing of 1.063" which is item #L44649. I recommend the Trailer Idler Hub Assembly for 2K Axles item #AKIHUB-545-2-LF-2K or…

view full answer...

Answer 2

If you want parking brakes for your 2015 Jayco Jay Sport 8SD then you do want to go with the Dexter Electric Trailer Brake Kit #K23-103-104-00. Parking brakes aren't required so if you would rather use standard brakes then you can use the part…

view full answer...

Answer 3

I do have all of the components you will need to flip the axle on your tent trailer but there is not an all inclusive kit per se to do so. However, the kits are pretty basic as all they include are u-bolts, tie plates, and spring seats. For your…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 11

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Recommended Spring Seat for a 2,200 lbs Axle w/ a 1-3/4" Diameter

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching