6-Way to 6-Way Coiled Adapter for Flat Towed Setup

Question

Question:

We have a 2001 Itasca with a 6 pin output plug. Our Versa also has a 6 wire input on the RM base plate. Ive not seen 6 to 6 except BO version with the plastic ends and not great reviews. Recommendations? It seems like all Ive located are 7 blade items. Thank you in advance

asked by: S S

0

Expert Reply:

Hey Stewart, so the only option would be the Blue Ox coiled adapter part # BX8862. We've sold quite a few of these and all of the feed back has been really good. I feel very confident recommending this for you.

expert reply by: Jameson C

0

Answer 1

The first thing you need to flat tow your 2010 Honda Fit is a base plate kit like the Roadmaster EZ part #521190-1 which is a confirmed fit. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and…

view full answer...

Answer 2

The wiring used for flat towing a vehicle is different than what you would use to tow a trailer with your 2001 Chevy Tracker so while I can definitely help you out with wiring, it will need to be a splice-in application instead of using the plug that…

view full answer...

Answer 3

For flat towing a 2011 Nissan Versa, You will need a base plate kit, tow bar, safety cables, wiring, supplemental braking system, and a possible high-low adapter. I have attached my recommendations on each of the following below. Flat-Tow Wiring:…

view full answer...

Answer 4

In order to have a wiring extension with 2 vehicle end connectors on it, you will want to create your own extension. We do not carry a pre-wired extension with 2 vehicle end 6-pole connectors. You will want to use 2 of the Pollak 6-Pole, Round Pin,…

view full answer...

Answer 5

Roadmaster uses a specific connection style for their locks, so for a lock set that would lock the base plates to the vehicle and the tow bar to the hitch of the tow vehicle you would want part #RM-304 or part #RM-302 for just the base plate locks.…

view full answer...

Answer 6

To install the RoadMaster 6-Wire Trailer Connector, part #RM-910030-7, you will need a bracket. The bracket I recommend is the Roadmaster Bent Electrical Socket Bracket, part #RM-910030-5. You need to find a flat surface that can support the…

view full answer...

Answer 7

The general reason a battery needs to be disconnected for flat towing is because there are certain functions that need to be disabled to prevent your vehicle's battery from draining. You wouldn't want to get to your destination and unhook and…

view full answer...

Answer 8

I pulled up the owners manual for your 2009 Nissan Versa and the standard transmission versions of the vehicle can be flat towed but there is no mention of needing to leave the key in the on position to keep the wheel unlocked. This is most likely…

view full answer...

Answer 9

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 10

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...