Replacement Hub/Drum and Brake Parts For a Mobile Home Axle

Question

Question:

I’d like to replace both brake and hub assemblies on one of the axles on my triple axle flatbed. The trailer was homemade in the early 1980s and I bought it from somebody a few weeks ago. The bearings must not have been in great shape as one failed and the entire wheel and hub assembly came off while I was driving the other day. The trailer capacity is 15k lbs, so I’m assuming this axle is in the 5k capacity range. The axle is about 61.5” from hub to hub and 75” overall. The tires/rims are 8-14.5” with a 5 spoke pattern. I’ve included photos. Do you have anything that would work?

asked by: Dustin D

0

Mobile Home Trailer Hub
(click to enlarge)

Expert Reply:

Based on your image it appears you have an old mobile home axle on our trailer. These axles were designed to not be rebuilt and thrown away when they became damaged which is why you saw complete axle assemblies carried as spares on the trucks that hauled the mobile home to its destination. If you can disassemble one of the hubs and measure the spindle and hub for the correct size bearings, races and grease seals I can see if we have anything that will fit your hubs. Otherwise for an exact replacement size axle you would have to have them special ordered from a local trailer dealer.

expert reply by: Bud M

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement Hub/Drum and Brake Parts For a Mobile Home Axle

Product Page this Question was Asked From

Continue Researching