Extension Cables for the Go Power Overlander Expansion Kit 34282182

Question

Question:

Hi. Looking at the go power 200 w expansion kit. I have one mounted already. What else will I need. Think extra wire to connect the two to the main input on roof. Do I need any other adapters?

asked by: Kurtis

0

Expert Reply:

The Go Power Overlander Expansion Kit - 200 Watt Solar Panel item # 34282182 has everything you need to connect to your existing Go Power Kit with the exception of extension cables. I have listed the lengths available below:

10' Go Power MC4 Output Cable item # 34276216

15' Go Power MC4 Output Cable item # 34279532

30' Go Power MC4 Output Cable item # 34276215

expert reply by: Jerred H

0

Kurtis

3/25/2024

Thanks. I also saw a 3 foot connector. Is that the same as the other ones you mentioned. Not sure if I need 10 feet

Reply

Jerred H.

3/28/2024

@Kurtis The 3' cable you were looking at has a SC4 connection. The Go Power Overlander Expansion Kit - 200 Watt Solar Panel item # 34282182 requires a MC4 connection and the shortest one we have is the 10' Go Power MC4 Output Cable item # 34276216.

Reply

Answer 1

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 2

You can use the Loctite RTV 598 High-Performance Silicone Gasket Maker #LT37467 as a sealant. You'll just want to put this sealant in between the two surfaces.

view full answer...

Answer 3

Yes, since you already have two Go Power Overlander Expansion Kit #34282182, you will need to add the MC4 expansion branch connectors #GP22VR and #GP82VR, as well as some extension cables to be able to add a third panel. You should also verify that…

view full answer...

Answer 4

For 10 foot long Go Power Extension Cables to use with the Go Power Overlander Expansion part #34282182 that you referenced you'd need two of the part #34276216 and you'd be set. These do not require special tools to connect either. The…

view full answer...

Answer 5

Yes you'd easily be safe to add another Go Power Overlander Expansion Kit #34282182 to your GoPower setup that has a 30 amp controller. You'd be close to the max amperage but you'd be under the 30 amps pretty easily even if they were at…

view full answer...

Answer 6

Hey Don; good question and no other parts - including any type of adapter plate or mounting plate - is needed to mount the 30 Amp Go Power PWM Solar Charge Controller with Bluetooth #GP76QR. The #GP76QR comes with screws and is ready to be mounted…

view full answer...

Answer 7

The Go Power Overlander Expansion Kit - 200 Watt Solar Panel item #34282182 has everything you need to connect to your existing Go Power Kit with the exception of extension cables. I have listed the lengths available below: 10' Go Power MC4…

view full answer...

Answer 8

Hi Donald, Yes, a higher amperage charger, like the #GP76QR (30 amp), would be able to provide a faster recharge for your battery bank than a 10 amp controller like the #34280503. When adding in the second battery you'll want to wire it in…

view full answer...

Answer 9

It sounds like you already have the Bluetooth Remote Display for Go Power MPPT Solar Charge Controllers #GP37MR with the Go Power MPPT Solar Charge Controller #GP72RR. The Remote Display for Go Power MPPT #GP37MR actually uses a bluetooth app as…

view full answer...

Answer 10

If your Thor Motorhome has a cable entry plate like part #34273840 on the roof then yes, you can attach the Go Power Overlander Expansion Kit #34282182 to it. You'll also need a controller like the PWM Solar Charge Controller #34280503 so you can…

view full answer...

Extension Cables for the Go Power Overlander Expansion Kit 34282182

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching