Inner Bracket Dimensions for Buyers Products Hitch Plate with 2" Receiver Tube - Ford

Question

Question:

What’s the inside dimension where the chassis would be? It looks like the 35 1/4 is outside to outside.

asked by: Adam

0

Expert Reply:

The inner bracket width of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford # 3371809060A is 34-1/4" plus or minus 0.06" according to my contact at Buyers Products.

Attached is a photo showing this dimension for you.

expert reply by: Jon G

0

Inner Bracket Dimensions for Buyers Products Hitch Plate with 2" Receiver Tube - Ford
(click to enlarge)

Answer 1

Yes we do; I have added a photo below for you of the dimensions of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford #3371809060A.

view full answer...

Answer 2

The Buyers Products Hitch Plate with 2" Receiver Tube - Ford #3371809060A will fit Ford models F350/F450/F550 but is designed for the cab and chassis models so if you have the regular pickup bed this may not work and you'll want to consult…

view full answer...

Answer 3

We may have a solution for you. To wire a brake controller on your 2007 International Trucks 4300 Series, you need to wire the controller's red wire to the stop light circuit. If the only wire you've found for brake lights is tied to the turn…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

The inner bracket width of the Buyers Products Hitch Plate with 2" Receiver Tube - Ford #3371809060A is 34-1/4" plus or minus 0.06" according to my contact at Buyers Products. Attached is a photo showing this dimension for you.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Inner Bracket Dimensions for Buyers Products Hitch Plate with 2" Receiver Tube - Ford

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching