Replacement Safety Pins for Roadmaster Jeep D-Rings

Question

Question:

What is the clip part that goes into this hitch pin for the roadmaster flat tow?

asked by: Robert

0

Expert Reply:

I checked with Roadmaster and the Replacement Safety Pins for Roadmaster Falcon and Eagle 8000 Tow Bars item # RM-910026 is what's used to secure the Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters item # RM-910044. They use it on quite a few of their adapters, tow bars, and base plates.

expert reply by: Jerred H

0

Answer 1

The Replacement Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters #RM-910044 are 7/8" in diameter as they can fit in both 7/8" and 1" diameter mounting holes.

view full answer...

Answer 2

Based on the information you have given me you have the Roadmaster Adapter for Jeep D-Ring Bumper Mounts to Roadmaster Motor Home Mount Tow Bars #RM-035 or #RM-035-1. Since you want to stick with Roadmaster parts, the correct replacement pin is the…

view full answer...

Answer 3

The correct lynch pins to use with the Roadmaster Hitch Pin for Roadmaster Jeep D-Ring Bumper Mount Tow Bar Adapters #RM-910044 is the #RM-910024. These are sold in a pair.

view full answer...

Answer 4

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement Safety Pins for Roadmaster Jeep D-Rings

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching