Timken Bearing kit for Dexter 4,400 lb Trailer Axle

Question

Question:

I am looking for a bearing kit for dexter 4400lb axles. Preferably Timken if you have it. Thanks in advance

asked by: Jeremy D

0

Expert Reply:

We have the individual components of a bearing kit available for a Dexter 4,400 lb trailer axle but since it's a rarer axle capacity we don't have a bearing kit. So for a Timken set you'd want the part # TMK49FR and # TMK56FR and then for a grease seal # 58846.

expert reply by: Jameson C

0

Answer 1

The pricing algorithm can be messed up from time to time but I do know that things like availability, supply and demand, and what other places are pricing it as well have an effect on this. I'll send in a message to our pricing team to look…

view full answer...

Answer 2

Yes, you can switch from using a Tang Washer #5-101 to the Spindle Nut Kit #RG05-100. This kit includes 2 Retainers #6-190, 2 Nuts #6-191 and 2 D-Washers #5-23.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 10

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Timken Bearing kit for Dexter 4,400 lb Trailer Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching