How Do I Connect the Brake Controller to My 2014 Jeep Grand Cherokee
Question:
I have a 2014 Jeep Grand Cherokee. It did not come with the trailering package. I had a factory hitch installed with the 7 Way plug the wiring was already in place at the rear of the the vehicle. What do I need and how do I connect the controller? Thanks
asked by: Briggs
Expert Reply:
If you do not already have a brake controller, I recommend a proportional type of brake controller like the Tekonsha Brake Controller part # 90885.
The only wire Jeep provides is the electric brake output wire that goes back to the 7-Way trailer connector. This wire is probably a light green wire that is behind the in-cab fuse box. It will connect to the blue wire on the brake controller.
You will still need to wire the black, white, and red wires on the brake controller. Both the black and white wires will be routed through the firewall, into the engine compartment, and over to the battery. You will need the Draw-Tite Brake Controller Wiring Kit, part # 5506.
Attach the black wire on the brake controller to the black wire in the duplex cable. Attach the white wire on the brake controller to the white wire on the duplex cable. Route the duplex cable through the firewall to the battery. Separate the two wires and connect the white wire to the negative battery terminal. Connect the black wire to the included 30-amp breaker (you might need a 20-amp breaker (# 9506P), check the brake controller instructions for which size breaker to use). The breaker can be mounted on the fire wall or near the battery. Then connect a wire from the breaker to the positive battery terminal.
Last, use a circuit tester like part # PTW2993, to find the brake light wire on the stop light switch located above the brake pedal. Find the wire that carries a signal ONLY when the brake pedal is pressed. Attach this wire to the red wire on the brake controller. Once you have the brake controller mounted the installation will be complete.
Products Referenced in This Question
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
In-Line Circuit Breaker - 20 Amp - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 20 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: Most Popular Wheel Bearings
- Q&A: Brake Controller Recommendation for a Truck with Air Brakes and a Trailer with Electric Brakes
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: Parts Needed to Install 7-Way/4-Way on 2024 Kia Telluride with LED Taillights
- Q&A: How do I Tell if the Brake Controller is Bad
- Q&A: Lift Kit Options For A 2015 Winnebago Micro Minnie 1706FB