Recommended Replacement Grease Seal for a 3109 Seal

Question

Question:

Hi customer service, I am looking 2 grease seals # 3109 5m for axle, if you carry please let me know, thanks.

asked by: Jose M

0

Expert Reply:

For your 3109 grease seals, you can use the Grease Seal # 1105-100-035 for replacements. This grease seal has the same measurements (2" I.D. | 2.875" O.D.) as your current seal and has a thickness of .3".

expert reply by: Bryce D

0

Answer 1

The seal part #1105-100-035 that you referenced has an inner diameter of 2.00 inches, an outer diameter of 2.875 inches and is .3 of an inch in thickness.

view full answer...

Answer 2

The closest grease seal we have is the part #1105-100-035 which has an ID of 2.000 and an OD of 2.875. You might measure your seal again to be sure it would be an exact fit. We don't have HADCO brake shoes but we do have replacement 12x2 brake…

view full answer...

Answer 3

Though we do have the replacement bearings, races, and seals available for your Hadco 3109 hub (which I have listed below), the combination used will not have an equivalent replacement hub available, unfortunately. Replacement Trailer Hub Bearing…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Recommended Replacement Grease Seal for a 3109 Seal

Product Page this Question was Asked From

Continue Researching