Recommended Moving Dolly for a B&W Continuum Head Assembly

Question

Question:

Is there a lift/dolly you can recommend for helping to remover the Head assembly when it isnt being used? Thx

asked by: BrianS

0

Expert Reply:

Hey Brian, the B&W Continuum Weight Distribution Head Assembly # BW48FR only weighs 52 lbs, so you should be able to easily remove it and put it on a moving dolly like the Snap-Loc Pushcart with E-Track Anchor Points # SL1500PTR319-P.

This dolly has a 33" tall handle to make moving the head around easy, has a 1,500 lb capacity, and when you're done using the dolly you can remove the handle for compact storage.

expert reply by: Bryce D

0

Answer 1

Yes, the B&W Continuum Weight Distribution System #BW78FR can be installed as easily on your angled driveway as it can be on level ground.

view full answer...

Answer 2

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 3

To be completely honest the sway control feature of the B and W Continuum part #BW78FR isn't nearly as advanced as the rest of the system. The advertised sway control of this system is in the head of the system between where the ball and the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Tom, you are on the right track. I checked out your 2023 Jayco Jay Flight 284 BHS and it does have an underslung coupler so the correct B and W Continuum weight distribution would be the part #BW88FR. An underslung coupler is basically one that…

view full answer...

Answer 6

The B&W Continuum #BW78FR and the Reese Strait-Line #RP66083 are both great systems. The B&W Continuum is going to be easier to set up, but as far as sway control goes, I definitely have to give the edge to the Reese Strait-Line. The…

view full answer...

Answer 7

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 10

That is definitely a feature which worries me about the B&W Continuum Weight Distribution System #BW78FR. While there is not a specific measurement I can give you as the bars move up and down depending on the load placed on the bars, B&W…

view full answer...

Answer 11

The B&W Continuum Weight Distribution System part #BW78FR requires at least 24" of space on the frame directly behind the coupler and along the side a few inches back from there. This works with most trailers but for some it will not and,…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Recommended Moving Dolly for a B&W Continuum Head Assembly

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching