Is The Dump Door Hinge for Dump Trailers # PLR1904-Z Able To Open 180 Degrees?

Question

Question:

Will this door hinge open 180 degrees or more? Or does it stop at a certain point?

asked by: Will

0

Expert Reply:

The Dump Door Hinge for Dump Trailers # PLR1904-Z is capable of opening over 180 degrees. While there are no stops built into the hinge do understand that it can open less than 180 degrees depending on your door/frame and how the hinge is installed.

expert reply by: Bud M

0

Answer 1

The Air Lift Air Helper Spring Cradles #AL59DQ are not going to be compatible with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL57589 on your 2021 Ram 2500. This is due to the 7500 springs being larger in diameter than the 5000…

view full answer...

Answer 2

Not super easily as it wasn't designed for that to happen regularly, but the bolt of the Dump Door Hinge #PLR1904-Z could be removed and the two pieces of the hinge could separate.

view full answer...

Answer 3

We don't have exactly what you are looking for. The #PLR1904-Z you referenced is 3-1/8 inch without the strap. The best other option is the Ramp Door Hinge - Steel #PLR1902 which utilizes as different hinge style and welds flat. It is 4 inches…

view full answer...

Answer 4

Most dimensions of the Polar Steel Dump Door Hinge #PLR1904-Z do appear on the photo from our website, which I linked for you, but I also went to our warehouse and measured the item to give two additional dimensions. These are shown on the second…

view full answer...

Answer 5

While we do have a hinge that is going to let you have a gate that swings to the inside of the trailer and to the outside for a 270 degree swing, the hinges you referred to would not allow that type of movement. Instead, you will need what is called…

view full answer...

Answer 6

You probably could rig your damaged wiring harness in the way you describe, using diodes to keep the circuits separated, but I suggest just replacing the harness with a 4-pole set-up like # C59496. This is a hardwired harness with a substantial…

view full answer...

Answer 7

The diode kit part #48955 that you referenced is designed to activate the running lights, turn signals, and brake lights. On each side of your vehicle two diodes are used. One is for the stop/turn circuit and the other for the running light circuit.…

view full answer...

Answer 8

You can use an isolating diode kit like #48955 to prevent tail light back-feeding in your flat towing set-up. Each stop and turn circuit (4 in total) will need a diode to allow signals to travel in only one direction, without back-feeding to the RV.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Is The Dump Door Hinge for Dump Trailers # PLR1904-Z Able To Open 180 Degrees?

Product Page this Question was Asked From

Continue Researching