Front Mount Trailer Hitch for an RV Built on a 2013 Ford E-350 Van Chassis

Question

Question:

I have a RV built on a E-350 van 2013 will this hitch fit

asked by: Rick W

0

Expert Reply:

Draw-Tite front mount trailer hitch # 65053 does indeed fit your RV built on a 2013 Ford E-350 van chassis. There is a plastic air deflector/fascia that must be trimmed or removed to install the hitch. I have included a link to the installation details so you can see what all is involved in the installation.

expert reply by: Michael H

0

Answer 1

The E-450, is a van chassis that your 2016 Thor RV is built on, which is different from the F chassis you also looked at. The front hitch that you will need for the E-450 chassis on your Thor is #65053. I have linked the above mentioned product to…

view full answer...

Answer 2

I assume you meant E-450, not F-450 which are not used as motorhome chassis. If that's the case then you'll need to use the Draw-Tite Front Mount Trailer Hitch Receiver part #65053 which is the only confirmed fit. It would work great…

view full answer...

Answer 3

We do offer hitch extenders which can be used for towing but the big thing to keep in mind when using such adapters is capacity, as they reduce this by 50%. The longest extender we offer for standard applications is 18" like the Trailer…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

The B and W Companion hitch part #BWRVK3370 that you referenced does not come assembled. The head will come in one box, and the slider setup will be separated out into two more boxes. I attached a link to the install instructions for you to check out…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Front Mount Trailer Hitch for an RV Built on a 2013 Ford E-350 Van Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching