Can a Trailer that Requires a 2-5/16 Inch Ball be Towed Using a 2 Inch Ball

Question

Question:

Can I tow a trailer that has a 2 5/16 Hitch on a 2 inch ball with it jump Off

asked by: Stan

0

Expert Reply:

You will want to match the ball you use with what the trailer coupler requires. It is definitely possible that the coupler could come off of the ball if you are using a ball that is too small for the coupler.

We have many 2-5/16 inch balls. I have included a link to them for you. You will need to make sure that you get one that has the right shank diameter to fit your ball mount's ball hole.

expert reply by: Michael H

0

Answer 1

While I can sympathize with your issue, it is not safe to tow a trailer if you only have a 2" hitch ball and your trailer coupler is designed for a 2-5/16" hitch ball, even for a short distance; the insecure connection between hitch ball…

view full answer...

Answer 2

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Answer 3

Yes, Equal-I-Zer actually makes a 2 inch hitch ball for use with their weight distribution systems which is part #EQ91-00-6080. This would work well with the part #EQ37060ET if that is the kit you have.

view full answer...

Answer 4

The terminals on the interior of the Pollak 10-Terminal Junction Box are size 10, or .190 of an inch. You would need a ring terminal suitable for a #10 stud for a 10-12 gauge wire.

view full answer...

Answer 5

The Blaylock Wheel Chock part #EZ-JACK that you referernced should work just fine on a trailer with fenders like yours. I attached a picture that shows it being used on a trailer with fenders for you to check out plus a review video. The overall…

view full answer...

Answer 6

If your 1999 Dodge Ram Pickup has a 7-Way with a round U.S. Car Connector that plugs in to the rear of the 7-Way then it will be a simple matter to disconnect it from the existing one and connect it to the Hopkins Quick-Install #HM40940. The photo…

view full answer...

Answer 7

We can get you a ball mount with a longer shaft to help keep your trailer safe. Without knowing the rise or drop you need, or the weight capacity, I can only offer a couple of general recommendations for ball mounts with long shafts. Since you have a…

view full answer...

Answer 8

We do have the correct repair kit for your coupler as the Demco Coupler Repair Kit #DM5696 will only work on the leverlock 2" coupler or model DA66 brake actuator. The Trigger Latch Repair Kit for A-Frame Couplers #CA-5100-RK is the correct…

view full answer...

Answer 9

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.

view full answer...

Answer 10

The Reese Sway Control Kit part #83660 can be bolted to the frame of your enclosed trailer. And if you use the ball mount bracket part #RP26003 you wouldn't have to have a tab welded to your ball mount either.

view full answer...

Answer 11

On the coupler typically you will see the size hitch ball it is designed to fit stamped or printed. It is possible that somebody removed he original coupler that was on your trailer and replaced it with one that has a 2 inch ball. Especially…

view full answer...

Answer 12

The Swagman RV Bumper 2 inch Trailer Hitch Receiver is intended to fit bumpers that measure 4 inches by 4 inches, and would not fit the bumper of your motorhome. The closest we come to the 4 inches by 1-1/2 inches you said is the size of your bumper…

view full answer...

Can a Trailer that Requires a 2-5/16 Inch Ball be Towed Using a 2 Inch Ball

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching