Will Timbren Springs Fit a 2005 Toyota Tacoma with Modified Rear Suspension

Question

Question:

i have a 05 tacoma 4 door with a 2inch add leaf lift. there is 7inch from the frame to the leafs is this the wright part

asked by: Mitch

1

Helpful Expert Reply:

Timbren springs # TTORTUN4 are designed for a 2005 Toyota Tacoma with 4 leaf springs on the rear suspension. If you have additional leaf springs then this kit would not fit because it sits between the leaf spring stack and the bump stop bracket.

But you mentioned that there is 7 inches of clearance from the frame to the top of the leaf spring stack below. The Timbren kit requires 6-1/4 inches to fit so it does not seem like there would be interference. Make sure that when you took the measurement that it was done with no weight in the vehicle.

expert reply by: Michael H

1

Answer 1

I went out and pulled both the Timbren kit part #TTORTUN4 and #TTORTUN4L from our warehouse to measure them for you and found that they both sit exactly 3-3/4 inches tall.

view full answer...

Answer 2

The correct Timbren Rear Suspension Enhancement System for a 2019 Toyota Tacoma is part #TTORTUN4L if you have three leaves in the rear leaf spring pack or part #TTORTUN4 if you have four leaves in the rear leaf spring pack. Therefore, the main…

view full answer...

Answer 3

I checked with Timbren and for your 2016 Toyota Tacoma they recommend the part #TTORTUN4L as a confirmed fit and not the #TTORTUN4. I attached a review video for you to check out as well.

view full answer...

Answer 4

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 5

Hey Tarek, for your 2023 Ford Raptor I recommend checking out the Timbren Suspension Enhancement System #T75MR. This suspension enhancement system has a load leveling capacity of 3,000 lbs, will increase stability while reducing sag, and will install…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes Tarek, the Timbren Suspension Enhancement System #T75MR will work fine with your 2023 Ford Raptor.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The correct Roadactive kit that fits your 2023 Ford F-150 is the part #RAS3611-YHD. I really like the RAS kits as they basically don't have any downsides. You get the adjustable support, an easy install, no maintenance, and actually improves…

view full answer...