What 5 On 4-1/2 Hub Will Fit The Timbren Axle-Less Trailer Suspension ASR3500S06?

Question

Question:

Which 5 by 4.5 Hub option would fit this axle?

asked by: Brian

0

Expert Reply:

The Timbren Axle-Less Trailer Suspension # ASR3500S06 uses the standard # L68149 inner and # L44649 outer bearings. So you can use virtually any standard 3.5K axle hub. For a 5 on 4-1/2 hub we suggest the following options:

Idler Hub # AKIHUB-545-35-G-EZ-K
Hub and Drum # AKHD-545-35-G-EZ-K

If you do need to set it up with electric brakes, we suggest using the above hub/drum, along with the # AKEBRK-35-SA Electric Brake assembly.

expert reply by: Jesse M

0

Answer 1

Yes, we do carry a Timbren Axle Less system that has a 3,500 lb capacity and a 4 inch lift. For that you'd want the part #ASR3500S06. This is a great axle solution for a trailer and it really doesn't have a downside. You'll…

view full answer...

Answer 2

The bolt pattern of 6 on 4-1/2 inch isn't a standard trailer bolt pattern so none of the hubs we offer will have it. You might want to double check the bolt pattern to see if maybe you have something different. I attached an FAQ article on…

view full answer...

Answer 3

The Timbren axle-less suspension kits are offered in either 4-on-4 or 5-on-4-1/2 bolt patterns; none is available with a 8-on-6-1/2 pattern idler hubs. All such kits are shown on the linked page. Several of these 3500-lb kits, parts #ASR3500S06,…

view full answer...

Answer 4

Based on what you listed wanting the Timbren Axle Less kit part #ASR3500S06 would be exactly what you want. You'll gain a lift of right at 4 inches and your current hub/drums and brake assemblies will easily transfer to it as you have 3,500 lb…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

There typically aren't any part numbers stamped onto the trailer spindle that can be used for identification. There are however numbers stamped onto the hub most times which can be used for identification. The TDE46210 tells me you have a 3,500…

view full answer...

Answer 9

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 12

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

What 5 On 4-1/2 Hub Will Fit The Timbren Axle-Less Trailer Suspension ASR3500S06?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching