Parts Needed to Rewire an 18' Trailer with a Set of Brakes and 6-Pin Connector
Question:
Yesterday I inquired about a light/wiring/pigtail kit to rewire my equipment hauling trailer, 18x7.5 tandem axle, with electric brakes on a single axle and a 6 pin pigtail. The response I got was questionable to me as the recommended kit looked like it only fit a single axle smaller utility trailer without brakes and only a 4 pin connector. Please advise me on which kit that you sell that will completely rewire my larger 18 trailer as described in my first sentence above. Thanks in advance for your time and cooperation.
asked by: David D
Expert Reply:
Here are the parts I recommend using to replace the wiring on your 18' trailer with a set of brakes and a 6-pin connector:
- Pollak 6-Pole, Round Pin, Trailer Wiring Connector # PK11604
- 25 Ft 4-Way Trailer Wiring Harness - Wishbone Style # A25W2GWB
- 10 Gauge Wire # 10-1-1 (sold by the foot)
- Butt Connector Kits # DW05745-5 and # DW05744-10
You'll use the wishbone style harness to route wiring from your lights to the connector, but then you'll cut off the 4-Way and connect that end of the wiring to the Pollak 6-Pole connector I referenced. The 10 gauge wiring is what you need for your trailer brakes, and the butt connectors are the best and easiest way to ensure your wiring connections are protected.
If you have any questions about these parts or you have a different style of connector please feel free to reach out!
Products Referenced in This Question
25 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 25' Ground
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 21 - 30 Feet Long
- Plug and Lead
- 4 Flat
- Optronics
more information >
Deka Heat Shrink Butt Connector - 16-14 Gauge - Nylon Insulation - Blue - Qty 10
- Wiring
- Wire Connectors
- Butt Connectors
- 16-14 Gauge
- Deka
more information >
Deka Heat Shrink Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 12-10 Gauge
- Deka
more information >
Product Page this Question was Asked From
Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- Plug Only
- 6 Round
- Pollak
more information >
Continue Researching
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Master Cylinder And Shock For UFP A-60 / A-75 / XR-84 Surge Brake Actuators
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Q&A: Bearings and Seal Used for AL-KO 7290 Trailer Hubs for #99 Spindles
- Q&A: Does B and W Gooseneck Hitch # BWGNRK1217 Fit 2017 Nissan Titan XD Long Bed
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Can Sway Control Be Used on a Trailer that Uses a Pintle Hitch Set Up
- Q&A: Replacement Landing Gear Motor for Venture M-9000-PK Motor and Replacement Aluminum Gearbox
- Q&A: Replacing 6-Way on Trailer With 7-Way Connector
- Q&A: Replacement Studs for RVD-H-865 7k Hub/Drum
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Can You Flat Tow a Ford Ranger