Replacement Camera for Furrion Vision S Monitor FOS07TAPT

Question

Question:

Hi, My rear Furrion camera is very blurry, almost cant make anything out. Its been cleaned and really no improvement. I think we need to replace it. Do you know which camera I would order? Ill attach a picture of the numbers on the back of the camera. Thank you!!

asked by: Linda B

0

Expert Reply:

Thank you for all of your info!

Your monitor is from the Furrion Vision S series of back up camera systems so to replace your camera you just need the Furrion Vision S Wireless RV Backup Camera w/ Night Vision # FCN48TASF.

expert reply by: Jon G

0

Furrion Vision S Monitor FOS07TAPT
(click to enlarge)

Answer 1

According to my research your Suburban water heater uses the anode rod part 232767 which matches the 3/4" Diameter x 9-1/2" Long dimensions of the Camco RV Water Heater #CAM11563, so this Camco replacement will work for you!

view full answer...

Answer 2

The Replacement 4.3" Monitor #FR77FR is not compatible with the older Furrion camera that you have. The manufacturer quit producing that monitor and none are available. I recommend upgrading your entire system to the Furrion Vision S Wireless RV…

view full answer...

Answer 3

Hey Rosemary; I'm happy to verify for you it is compatible. The #FRCBRKT-BL is actually the bracket for the camera but is the Vision S system. But the camera that mounts to that bracket will absolutely work with the Replacement 5" Monitor…

view full answer...

Answer 4

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 5

Hey William, the E6 error on a Furrion wall thermostat indicates an Open circuit Humidity Sensor issue. Most likely the sensor is bad and needs to be replaced as this is a pretty rare error code.

view full answer...

Answer 6

For the 7-way pigtail/junction box, I'd recommend the #277-000141 junction box/pigtail which will do a good job of keeping the water out unless it's submerged. Adding a bead of silicone caulk around the seams where the lid meets the box and…

view full answer...

Answer 7

That is a good question, but no type of special inverter is required in order for you to use the Go Power AGM RV Battery - Deep Cycle - Group 27 - 12V - 100 Amp Hour #34276285. This battery is absolutely compatible with a standard inverter so you…

view full answer...

Answer 8

There is no longer a compatible replacement camera available for your older Furrion system. This particular system has been replaced and the new replacement camera #FCN48TASF is not compatible. I confirmed this with my contacts at Furrion. You'll…

view full answer...

Answer 9

Hey Kevin, so the Bearing Buddy part #BB2717SS does fit the Lippert 7k axle so it is the correct size BUT you will need to yank the zerk fitting off your EZ lube style spindle. I would first try putting vice grips on the zerk so that you can focus on…

view full answer...

Answer 10

Thank you for all of your info! Your monitor is from the Furrion Vision S series of back up camera systems so to replace your camera you just need the Furrion Vision S Wireless RV Backup Camera w/ Night Vision #FCN48TASF.

view full answer...

Answer 11

When you are replacing bearings you do want to pack them prior to installing the new ones into your hub. This ensures that the grease actually gets pushed completely into the bearings so that they work properly and don't overheat. You can use a…

view full answer...

Answer 12

If you want to use a Bearing Buddy on a trailer hub that currently has a Sure Lube grease cap you certainly could. Essentially the design between the two is the same.

view full answer...

Replacement Camera for Furrion Vision S Monitor FOS07TAPT

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching