Do I Need a Capture Plate for a Rota Flex Pin Box?

Question

Question:

Do I need a locking plate with a standard Rota Flex pin box?

asked by: Alex

0

Expert Reply:

Yes, you do. The correct one to use with the Demco Autoslide item # DM79GV is the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes item # DM6171.

The Demco Autoslide 5th Wheel Hitch w/ Slider item # DM79GV you were looking at is confirmed to fit the puck system of the 2024 GMC Sierra 2500.

expert reply by: Jerred H

0

Answer 1

If this is a new hitch Demco states that the first few times you use a Hijacker like the part #DM8550034 some of the moving mechanisms might need a few uses to "wear in" and move easier. If the hitch is older and is now starting to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 5

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 6

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 7

Hi David, Rock Tamers require an inch of space on the ball mount shank in order to mount. If the portion of the shank exposed where you'll be installing the Rock Tamers is 2" x 2" then you'll want #ERT00108, for 2.5" x…

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

We still recommend the use of a slider in all standard/short bed trucks. That being said, the new GM trucks like your 2022 GMC Sierra 2500 do have a slightly longer bed than the typical standard bed. The best thing you can do is to measure to see if…

view full answer...

Answer 10

There are a select few fifth wheel hitches that have replacement leg kits that would adapt them to fit the OEM prep package of your Dad's 2023 GMC Sierra 3500 but I would need to know what hitch you guys have to be able to determine if that's…

view full answer...

Answer 11

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 12

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Do I Need a Capture Plate for a Rota Flex Pin Box?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching